Toyota Camry (XV70): Adjusting the set speed - Dynamic radar cruise control
- Adjusting the set speed by the switch
To change the set speed, press the "+ RES" or "- SET" switch until the desired set speed is displayed.
- Increases the speed
- Decreases the speed
Fine adjustment: Press the switch.
Large adjustment: Press and hold the switch to change the speed, and release when the desired speed is reached.
In the vehicle-to-vehicle distance control mode, the set speed will be increased or decreased as follows:
For U.S. mainland and Hawaii
Fine adjustment: By 1 mph (1.6 km/h)*1 or 1 km/h (0.6 mph)*2 each time the switch is pressed
Large adjustment: Increases or decreases in 1 mph (1.6 km/h)*1 or 1 km/h (0.6 mph)*2 increments for as long as the switch is held
For Canada, Guam and Puerto Rico
Fine adjustment: By 1 mph (1.6 km/h)*1 or 1 km/h (0.6 mph)*2 each time the switch is pressed
Large adjustment: Increases or decreases in 5 mph (8 km/h)*1 or 5 km/h (3.1 mph)*2 increments for as long as the switch is held
In the constant speed control mode the set speed will be increased or decreased as follows:
Fine adjustment: By 1 mph (1.6 km/h)*1 or 1 km/h (0.6 mph)*2 each time the switch is pressed
Large adjustment: The speed will continue to change while the switch is held.
*1: When the set speed is shown in "MPH"
*2: When the set speed is shown in "km/h"
- Increasing the set speed by the accelerator pedal
- Accelerate with accelerator pedal operation to the desired vehicle speed
- Press the "- SET" switch
Changing the vehicle-to-vehicle distance (vehicle-to-vehicle distance control mode)
Pressing the switch changes the vehicle-to-vehicle distance as follows:
- Long
- Medium
- Short
Vehicle-to-vehicle distance settings (vehicle-to-vehicle distance control mode)
Select a distance from the table below. Note that the distances shown correspond to a vehicle speed of 50 mph (80 km/h). Vehicle-to-vehicle distance increases/decreases in accordance with vehicle speed.
Canceling and resuming the speed control
- Pressing the cancel switch cancels
the speed control.
The speed control is also canceled when the brake pedal is depressed. - Pressing the "+ RES" switch
resumes the cruise control and
returns vehicle speed to the set
speed.
However, cruise control does not resume when the vehicle speed is approximately 16 mph (25 km/h) or less.
READ NEXT:
Approach warning (vehicle-to-vehicle distance control mode) - Dynamic radar cruise
control
When your vehicle is too close to
a vehicle ahead, and sufficient
automatic deceleration via the
cruise control is not possible, the
display will flash and the buzzer
will sound to alert the driv
Selecting constant speed control mode - Dynamic radar cruise
control
When constant speed control mode is selected, your vehicle will maintain
a set speed without controlling the vehicle-to-vehicle distance.
Select this mode only when vehicle-to-vehicle distance con
Driving assist systems
To keep driving safety and performance, the following systems
operate automatically in response to various driving situations.
Be aware, however, that these systems are supplementary and
should n
SEE MORE:
Problem Symptoms Table
PROBLEM SYMPTOMS TABLE
NOTICE:
If the DCM (telematics transceiver) has been replaced, perform the DCM Activation procedure.
Click here
Before replacing the DCM (telematics transceiver), refer to Registration.
Click here
HINT:
Use the table below to help determine the cause
Short to GND in Outer Mirror Indicator(Master) (C1AB2)
DESCRIPTION This DTC is stored when the blind spot monitor sensor RH detects a short to ground in the outer rear view mirror indicator RH.
DTC No. Detection Item
DTC Detection Condition Trouble Area
C1AB2 Short to GND in Outer Mirror Indicator(Master) Both of the following
