Toyota Camry owners & service manuals

Toyota Camry (XV70): Turn Signal Light Circuit Current Below Threshold (B150718)

Toyota Camry Repair Manual XV70 (2018-2024) / Vehicle Interior / Meter / Gauge / Display / Meter / Gauge System / Turn Signal Light Circuit Current Below Threshold (B150718)

DESCRIPTION

This DTC is stored when the combination meter assembly detects an open in a front turn signal light circuit or rear turn signal light circuit.

HINT:

  • If there is an open in a front turn signal light circuit or rear turn signal light circuit, the turn signal lights on the side with the open circuit will blink faster than usual.
  • If there is an open in a side turn signal light circuit, DTC B150718 will not be stored.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

Memory

Note

B150718

Turn Signal Light Circuit Current Below Threshold

Diagnosis Condition:

  • Battery voltage is 10 V or more

Malfunction Status:

  • Open in front turn signal light circuit
  • Open in rear turn signal light circuit
  • Harness or connector
  • Headlight assembly
  • Rear combination light assembly
  • Combination meter assembly

DTC stored

-

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

  • When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
  • Inspect the turn signal light bulbs, sockets and wire harnesses before performing the following procedure.

PROCEDURE

1.

INSPECT LIGHTS

(a) Inspect the illumination of each turn signal light.

Result

Proceed to

Front turn signal light LH does not blink

A

Rear turn signal light LH does not blink

B

Front turn signal light RH does not blink

C

Rear turn signal light RH does not blink

D

B

GO TO STEP 5

C

GO TO STEP 6

D

GO TO STEP 9

A

2.

CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)

(a) Disconnect the A53*1 or A75*2 headlight assembly LH connector.

  • *1: for Bulb Type Turn Signal Light
  • *2: for LED Type Turn Signal Light

(b) Disconnect the K20 combination meter assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

for Bulb Type Turn Signal Light

Tester Connection

Condition

Specified Condition

A53-1 (B) - K20-11 (LL)

Always

Below 1 ?

A53-3 (E) - Body ground

Always

Below 1 ?

for LED Type Turn Signal Light

Tester Connection

Condition

Specified Condition

A75-2 (B) - K20-11 (LL)

Always

Below 1 ?

A75-8 (E) - Body ground

Always

Below 1 ?

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

3.

CONFIRM MODEL

(a) Choose the model to be inspected.

Result

Proceed to

for Bulb Type Turn Signal Light

A

for LED Type Turn Signal Light

B

A

REPLACE COMBINATION METER ASSEMBLY

B

4.

INSPECT HEADLIGHT ASSEMBLY LH

(a) Remove the headlight assembly LH.

Click here

(b) Inspect the headlight assembly LH.

Click here

OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE HEADLIGHT ASSEMBLY LH

5.

CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)

(a) Disconnect the W13 rear combination light assembly LH connector.

(b) Disconnect the K20 combination meter assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

W13-3 (B) - K20-10 (TRNL)

Always

Below 1 ?

W13-4 (E) - Body ground

Always

Below 1 ?

OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.

CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND)

(a) Disconnect the A52*1 or A74*2 headlight assembly RH connector.

  • *1: for Bulb Type Turn Signal Light
  • *2: for LED Type Turn Signal Light

(b) Disconnect the K20 combination meter assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

for Bulb Type Turn Signal Light

Tester Connection

Condition

Specified Condition

A52-1 (B) - K20-7 (LR)

Always

Below 1 ?

A52-3 (E) - Body ground

Always

Below 1 ?

for LED Type Turn Signal Light

Tester Connection

Condition

Specified Condition

A74-2 (B) - K20-7 (LR)

Always

Below 1 ?

A74-8 (E) - Body ground

Always

Below 1 ?

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

7.

CONFIRM MODEL

(a) Choose the model to be inspected.

Result

Proceed to

for Bulb Type Turn Signal Light

A

for LED Type Turn Signal Light

B

A

REPLACE COMBINATION METER ASSEMBLY

B

8.

INSPECT HEADLIGHT ASSEMBLY RH

(a) Remove the headlight assembly RH.

Click here

(b) Inspect the headlight assembly RH.

Click here

OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE HEADLIGHT ASSEMBLY RH

9.

CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND)

(a) Disconnect the W12 rear combination light assembly RH connector.

(b) Disconnect the K20 combination meter assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

W12-3 (B) - K20-13 (TRNR)

Always

Below 1 ?

W12-4 (E) - Body ground

Always

Below 1 ?

OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

    READ NEXT:

    SEE MORE:

     Diagnostic Trouble Code Chart

    DIAGNOSTIC TROUBLE CODE CHART Panoramic Moon Roof System DTC No. Detection Item Link B2341 Sensor (Motor) Failure B2341 Sensor (Motor) Failure B2342 Switch Failure B2342 Switch Failure B2343

     Diagnostic Trouble Code Chart

    DIAGNOSTIC TROUBLE CODE CHART Vehicle Stability Control System DTC No. Detection Item Link C00631C Yaw Rate Sensor Circuit Voltage Out of Range C00631F Yaw Rate Sensor Circuit Intermittent C006396 Yaw Rate Sensor Component Internal Failure

    © 2023-2026 Copyright www.tocamry.com