Toyota Camry (XV70): Customize Parameters
CUSTOMIZE PARAMETERS
NOTICE:
- When the customer requests a change in a function, first make sure that the function can be customized.
- Be sure to make a note of the current settings before customizing.
- When troubleshooting a function, first make sure that the function is set to the default setting.
HINT:
The following items can be customized.
CUSTOMIZE HEADUP DISPLAY SYSTEM
(a) Customizing with the Techstream
(1) Connect the Techstream to the DLC3.
(2) Turn the ignition switch to ON.
(3) Turn the Techstream on.
(4) Enter the following menus: Customize Setting / Display.
(5) Select the setting by referring to the table below.
Display|
Tester Display | Description |
Default | Setting |
ECU |
|---|---|---|---|---|
| Projection Adjustment (Tilt) |
Headup display image calibration (tilt calibration) |
Default | $03:Clockwise (+3),$02:Clockwise (+2),$01:Clockwise (+1),$00:Default,$FF:Anti-Clockwise (-1),$FE:Anti-Clockwise (-2),$FD:Anti-Clockwise (-3) |
Meter mirror sub-assembly |
|
Projection Adjustment (Keystone) |
Headup display image calibration (keystone calibration) |
Default | $03:Narrow Top (+3),$02:Narrow Top (+2),$01:Narrow Top (+1),$00:Default,$FF:Narrow Bottom (-1),$FE:Narrow Bottom (-2),$FD:Narrow Bottom (-3) |
Meter mirror sub-assembly |
|
Projection Adjustment (Distortion) |
Headup display image calibration (distortion calibration) |
Default | $03:Convex (+3),$02:Convex (+2),$01:Convex (+1),$00:Default,$FF:Concave (-1),$FE:Concave (-2),$FD:Concave (-3) |
Meter mirror sub-assembly |
|
Audio Information Display Function |
Audio system operation status display setting for headup display* |
ON | $00:OFF,$01:ON |
Meter mirror sub-assembly |
|
Master Caution Display Function |
Master warning light display setting for headup display |
ON | $00:OFF,$01:ON |
Meter mirror sub-assembly |
|
Speed Limit Display Function |
Speed limit display setting for headup display |
ON | $00:OFF,$01:ON |
Meter mirror sub-assembly |
|
Turn by Turn Animation Function |
Route guidance to destination display setting for headup display* |
ON | $00:OFF,$01:ON |
Meter mirror sub-assembly |
|
Traffic Sign Recognition Animation Function |
Traffic sign recognition display setting for headup display* |
ON | $00:OFF,$01:ON |
Meter mirror sub-assembly |
|
Memory Call Link Function |
Memory call link setting for headup display image position* |
ON | $00:OFF,$01:ON |
Meter mirror sub-assembly |
|
Seat Switch Link Function |
Power seat switch link setting for headup display image position* |
ON | $00:OFF,$01:ON |
Meter mirror sub-assembly |
|
ECO Drive Indicator Zone Display Function |
ECO driving indicator zone display setting for headup display |
ON | $00:OFF,$01:ON |
Meter mirror sub-assembly |
|
Projection Adjustment (Tilt) |
Headup display image calibration (tilt calibration)* |
Default | $05:Clockwise (+5),$04:Clockwise (+4),$03:Clockwise (+3),$02:Clockwise (+2),$01:Clockwise (+1),$00:Default,$FF:Anti-Clockwise (-1),$FE:Anti-Clockwise (-2),$FD:A**cut** |
Meter mirror sub-assembly |
HINT:
- Depending on the specifications of the vehicle, some items may not be displayed.
- *: Not applicable to this vehicle
(b) Customizing with the multi-information display
(1) Turn the ignition switch to ON.
(2) Select the setting tab and perform the customize setting from the multi-information display.
|
Display | Detail |
Description | Setting |
ECU |
|---|---|---|---|---|
|
HUD Brightness/Position |
Brightness | Display brightness setting for headup display |
- | Meter mirror sub-assembly |
|
Position | Display position setting for headup display |
- | Meter mirror sub-assembly | |
|
HUD Driving Support | Tachometer Settings |
Tachometer display setting for headup display |
Blank/Eco Indicator/Tachometer |
Meter mirror sub-assembly |
|
Navigation | Route guidance to destination display setting for headup display |
On/Off | Meter mirror sub-assembly | |
|
Driving Assist | Driving assist display setting for headup display |
On/Off | Meter mirror sub-assembly | |
|
Compass | Compass display setting for headup display |
On/Off | Meter mirror sub-assembly | |
|
Rotation | - |
Headup display image calibration (rotation calibration) |
- | Meter mirror sub-assembly |
HINT:
Depending on the specifications of the vehicle, some items may not be displayed.
READ NEXT:
SEE MORE:
Check Mode Procedure
CHECK MODE PROCEDURE HINT: Compared to normal mode, check mode is more sensitive to malfunctions. Therefore, check mode can detect malfunctions that cannot be detected in normal mode.
NOTICE: All the stored DTCs and freeze frame data are cleared if: 1) the ECM is changed from normal mode to check
Removal
REMOVAL CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during central gateway ECU (network gateway ECU) removal/installation are shown below. Necessary Procedures
