Toyota Camry owners & service manuals

Toyota Camry: Adjusting the set speed - Dynamic radar cruise control with full-speed range

Toyota Camry Owner's Manual XV70 (2017-2024) / Driving / Using the driving support systems / Adjusting the set speed - Dynamic radar cruise control with full-speed range

  • Adjusting the set speed by the switch

To change the set speed, press the "+ RES" or "- SET" switch until the desired set speed is displayed.

  1. Increases the speed
    (Except when the vehicle has been stopped by system control in vehicle- to-vehicle distance control mode)
  2. Decreases the speed
    Fine adjustment: Press the switch.

    Large adjustment: Press and hold the switch to change the speed, and release when the desired speed is reached.

Using the driving support systems

In the vehicle-to-vehicle distance control mode, the set speed will be increased or decreased as follows:

For U.S. mainland and Hawaii

Fine adjustment: By 1 mph (1.6 km/h)*1 or 1 km/h (0.6 mph)*2 each time the switch is pressed

Large adjustment: Increases or decreases in 1 mph (1.6 km/h)*1 or 1 km/h (0.6 mph)*2 increments for as long as the switch is held

For Canada, Guam and Puerto Rico

Fine adjustment: By 1 mph (1.6 km/h)*1 or 1 km/h (0.6mph)*2 each time the switch is pressed

Large adjustment: Increases or decreases in 5 mph (8 km/h)*1 or 5 km/h (3.1 mph)*2 increments for as long as the switch is held

In the constant speed control mode the set speed will be increased or decreased as follows:

Fine adjustment: By 1 mph (1.6 km/h)*1 or 1 km/h (0.6 mph)*2 each time the switch is pressed

Large adjustment: The speed will continue to change while the switch is held.

*1: When the set speed is shown in "MPH"
*2: When the set speed is shown in "km/h"

  • Increasing the set speed by the accelerator pedal

1. Accelerate with accelerator pedal operation to the desired vehicle speed

2. Press the "- SET" switch

Changing the vehicle-to-vehicle distance (vehicle-to-vehicle distance control mode)

Pressing the switch changes the vehicle-to-vehicle distance as follows:

  1. Long
  2. Medium
  3. Short

Using the driving support systems

Vehicle-to-vehicle distance settings (vehicle-to-vehicle distance control mode)

Select a distance from the table below. Note that the distances shown correspond to a vehicle speed of 50 mph (80 km/h). Vehicle-to-vehicle distance increases/decreases in accordance with vehicle speed.

When the vehicle is stopped by system control, the vehicle stops at a certain vehicle-to-vehicle distance depending on the situation.

Using the driving support systems

Resuming follow-up cruising when the vehicle has been stopped by system control (vehicle-to-vehicle distance control mode)

After the vehicle ahead of you starts off, press the "+ RES" switch.

Your vehicle will also resume follow- up cruising if the accelerator pedal is depressed after the vehicle ahead of you starts off.

Using the driving support systems

Canceling and resuming the speed control

  1. Pressing the cancel switch cancels the speed control.
    The speed control is also canceled when the brake pedal is depressed.
    (When the vehicle has been stopped by system control, depressing the brake pedal does not cancel the setting.)
  2. Pressing the "+ RES" switch resumes the cruise control and returns vehicle speed to the set speed.

Using the driving support systems

    READ NEXT:

     Approach warning (vehicle-to-vehicle distance control mode) - Dynamic radar cruise control with full-speed range

    When your vehicle is too close to a vehicle ahead, and sufficient automatic deceleration via the cruise control is not possible, the display will flash and the buzzer will sound to alert the driv

     Selecting constant speed control mode - Dynamic radar cruise control with full-speed range

    When constant speed control mode is selected, your vehicle will maintain a set speed without controlling the vehicle-to-vehicle distance. Select this mode only when vehicle-to-vehicle distance con

     Dynamic radar cruise control

    Summary of functions In vehicle-to-vehicle distance control mode, the vehicle automatically accelerates and decelerates to match the speed changes of the preceding vehicle even if the accelerator p

    SEE MORE:

     AV Signal Stoppage (Low Battery Voltage) (B158F)

    DESCRIPTION This DTC is stored when a video or audio signal is interrupted due to battery voltage input to the radio and display receiver assembly dropping temporarily. DTC No. Detection Item DTC Detection Condition Trouble Area B158F AV Signal Stoppage (Low Battery Voltage)

     Components

    COMPONENTS ILLUSTRATION *1 AUDIO AMPLIFIER COVER *2 STEREO COMPONENT AMPLIFIER ASSEMBLY WITH BRACKET ILLUSTRATION *1 NO. 1 AMPLIFIER BRACKET *2 NO. 2 AMPLIFIER BRACKET *3 STEREO COMPONENT AMPLIFIER ASSEMBLY - -

    © 2023-2024 Copyright www.tocamry.com