Toyota Camry (XV70): Camera ECU Malfunction (C1610)
DESCRIPTION
This DTC is stored when a malfunction occurs in the parking assist monitor system*1 or panoramic view monitor system*2.
|
DTC No. | Detection Item |
DTC Detection Condition | Trouble Area |
|---|---|---|---|
|
C1610 | Camera ECU Malfunction |
|
|
- *1: w/ Parking Assist Monitor System
*2: w/ Panoramic View Monitor System
CAUTION / NOTICE / HINT
NOTICE:
- Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.
Click here
.gif)
- When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:
- A communication malfunction DTC may be stored.
- The radio and display receiver assembly may not operate normally.
PROCEDURE
|
1. | CHECK MODEL |
(a) Choose the model to be inspected.
|
Result | Proceed to |
|---|---|
|
w/ Parking Assist Monitor System |
A |
| w/ Panoramic View Monitor System |
B |
| B |
.gif) | GO TO STEP 4 |
|
.gif)
| 2. |
CHECK DTC (PARKING ASSIST MONITOR SYSTEM) |
(a) Clear the DTCs.
Chassis > Parking Assist Camera > Clear DTCs(b) Recheck for DTCs and check that no DTCs are output.
Chassis > Parking Assist Camera > Trouble CodesOK:
No DTCs are output.
| NG | |
GO TO PARKING ASSIST MONITOR SYSTEM |
|
| 3. |
CHECK DTC (AUDIO AND VISUAL SYSTEM) |
(a) Clear the DTCs.
Body Electrical > Navigation System > Clear DTCs(b) Recheck for DTCs and check that no DTCs are output.
Body Electrical > Navigation System > Trouble CodesOK:
No DTCs are output.
| OK | |
END |
| NG | | REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY
|
| 4. |
CHECK DTC (PANORAMIC VIEW MONITOR SYSTEM) |
(a) Clear the DTCs.
Chassis > Panoramic View Monitor > Clear DTCs(b) Recheck for DTCs and check that no DTCs are output.
Chassis > Panoramic View Monitor > Trouble CodesOK:
No DTCs are output.
| NG | |
GO TO PANORAMIC VIEW MONITOR SYSTEM |
|
| 5. |
CHECK DTC (AUDIO AND VISUAL SYSTEM) |
(a) Clear the DTCs.
Body Electrical > Navigation System > Clear DTCs(b) Recheck for DTCs and check that no DTCs are output.
Body Electrical > Navigation System > Trouble CodesOK:
No DTCs are output.
| OK | |
END |
| NG | | REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY
|
READ NEXT:
Sending Malfunction (Navigation to APGS) (U0073,U0100,U0129,U0140,U0155,U0164,U0198,U023B,U0265,U1110)
DESCRIPTION These DTCs are stored when a malfunction occurs in the CAN communication circuit.
DTC No. Detection Item
DTC Detection Condition Trouble Area
U0073 Sending Malfunc
Satellite Radio Broadcast cannot be Received
CAUTION / NOTICE / HINT NOTICE: Some satellite radio broadcasts require payment. A contract must be made between a satellite radio company and the user. If the contract expires, it will not be possibl
Satellite Radio Broadcast cannot be Selected or After Selecting Broadcast, Broadcast cannot be Added into Memory
CAUTION / NOTICE / HINT NOTICE: Some satellite radio broadcasts require payment. A contract must be made between a satellite radio company and the user. If the contract expires, it will not be possibl
SEE MORE:
Pressure Control Solenoid "B" Actuator Stuck Off (P07757F)
DESCRIPTION Based on signals from the transmission revolution sensors (NT and NC), the actual gear is detected.
The ECM compares the actual gear with the shift schedule in the ECM memory to detect mechanical malfunctions of the solenoid valves, transmission valve body assembly and automatic transa
Blind Spot Monitor Master Module (C1AB6)
DESCRIPTION This DTC is stored when the blind spot monitor sensor RH detects an internal malfunction.
DTC No. Detection Item
DTC Detection Condition Trouble Area
C1AB6 Blind Spot Monitor Master Module
The blind spot monitor sensor RH (master) detects an internal malfun
