Toyota Camry (XV70): Components
COMPONENTS
ILLUSTRATION
|
*1 | NO. 2 PARKING BRAKE WIRE ASSEMBLY |
*2 | PARKING BRAKE ACTUATOR ASSEMBLY |
|
*3 | O-RING |
- | - |
.png) |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
● | Non-reusable part |
.png) |
Lithium soap base glycol grease |
- | - |
ILLUSTRATION
|
*1 | REAR DISC BRAKE ANTI-SQUEAL SHIM KIT |
*2 | REAR DISC BRAKE CYLINDER ASSEMBLY |
|
*3 | REAR DISC BRAKE PAD |
*4 | REAR FLEXIBLE HOSE |
|
*5 | REAR NO. 1 DISC BRAKE ANTI-SQUEAL SHIM |
*6 | REAR NO. 2 DISC BRAKE ANTI-SQUEAL SHIM |
|
*7 | REAR DISC BRAKE ANTI-SQUEAL SHIM |
*8 | REAR DISC BRAKE PAD WEAR INDICATOR PLATE |
|
*9 | GASKET |
*10 | UNION BOLT |
|
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
● | Non-reusable part |
|
|
Brake shim grease (Part No. 08887-80409) |
- | - |
ILLUSTRATION
|
*1 | REAR DISC |
*2 | REAR DISC BRAKE BUSHING DUST BOOT |
|
*3 | REAR DISC BRAKE CYLINDER MOUNTING |
*4 | REAR DISC BRAKE PAD SUPPORT PLATE |
|
*5 | REAR NO. 1 DISC BRAKE CYLINDER SLIDE PIN |
*6 | REAR NO. 2 DISC BRAKE CYLINDER SLIDE PIN |
|
*7 | REAR DISC BRAKE CYLINDER SLIDE BUSHING |
- | - |
|
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
● | Non-reusable part |
|
|
Lithium soap base glycol grease |
- | - |
ILLUSTRATION
|
*1 | CYLINDER BOOT |
*2 | PISTON SEAL |
|
*3 | REAR DISC BRAKE BLEEDER PLUG |
*4 | REAR DISC BRAKE BLEEDER PLUG CAP |
|
*5 | REAR DISC BRAKE PISTON |
*6 | REAR DISC BRAKE CYLINDER |
|
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
● | Non-reusable part |
|
|
Lithium soap base glycol grease |
- | - |
READ NEXT:
Removal
REMOVAL CAUTION / NOTICE / HINT
NOTICE:
Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to
Disassembly
DISASSEMBLY CAUTION / NOTICE / HINT
CAUTION: If the rear disc brake cylinder assembly has been disassembled, perform air bleeding for the rear disc brake cylinder assembly.
Click here
NOTICE:
Inspection
INSPECTION PROCEDURE 1. INSPECT BRAKE CYLINDER AND PISTON
(a) Check the rear disc brake cylinder bore and rear disc brake piston for rust and scoring. If necessary, replace the rear disc brake cylin
SEE MORE:
Components
COMPONENTS ILLUSTRATION
*1 COWL SIDE TRIM SUB-ASSEMBLY LH
*2 FRONT DOOR OPENING TRIM WEATHERSTRIP LH
*3 FRONT DOOR SCUFF PLATE LH
*4 HOOD LOCK CONTROL LEVER SUB-ASSEMBLY
*5 INSTRUMENT SIDE PANEL LH
*6 NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY
Installation
INSTALLATION CAUTION / NOTICE / HINT
HINT:
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
PROCEDURE 1. INSTALL REAR DOOR BELT MOULDING ASSEMBLY
(a) Engage the guide and 5 claws to install a new rear door belt moulding assembly as
