Toyota Camry owners & service manuals

Toyota Camry (XV70): Differential Oil Seal

Toyota Camry Repair Manual XV70 (2018-2024) / Drivetrain / Ua80e (automatic Transmission / Transaxle) / Differential Oil Seal

Components

COMPONENTS

ILLUSTRATION

*1

DRIVE SHAFT BEARING BRACKET

*2

FRONT DRIVE SHAFT OIL SEAL LH

*3

FRONT DRIVE SHAFT OIL SEAL RH

-

-

N*m (kgf*cm, ft.*lbf): Specified torque

●

Non-reusable part

Do not apply lubricants to the threaded parts

-

-

Replacement

REPLACEMENT

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front drive shaft oil seal LH and front drive shaft oil seal RH removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

Front wheel alignment adjustment
  • Perform "Reset Memory"
  • Perform acceleration sensor zero point calibration and system information memorization
  • VSC disabled or malfunctioning
  • DTCs are output
  • Slip indicator light illuminated
  • ABS warning light illuminated

Replacement of automatic transaxle fluid

ATF thermal degradation estimate reset

The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly.

PROCEDURE

1. REMOVE FRONT DRIVE SHAFT ASSEMBLY

Click here

2. REMOVE DRIVE SHAFT BEARING BRACKET

Click here

3. REMOVE FRONT DRIVE SHAFT OIL SEAL LH

(a) Using SST, remove the front drive shaft oil seal LH from the automatic transaxle case sub-assembly.

SST: 09308-00010

NOTICE:

Be careful not to damage the automatic transaxle case sub-assembly.

4. REMOVE FRONT DRIVE SHAFT OIL SEAL RH

(a) Using SST, remove the front drive shaft oil seal RH from the transaxle housing.

SST: 09308-00010

NOTICE:

Be careful not to damage the transaxle housing.

5. INSTALL FRONT DRIVE SHAFT OIL SEAL RH

(a) Using SST and a hammer, install a new front drive shaft oil seal RH to the transaxle housing.

SST: 09316-10010

SST: 09950-70010

09951-07150

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)

NOTICE:

  • Make sure that the front drive shaft oil seal RH is installed in the correct direction.
  • Do not damage the lip of the front drive shaft oil seal RH.

*a

Depth

6. INSTALL FRONT DRIVE SHAFT OIL SEAL LH

(a) Using SST and a hammer, install a new front drive shaft oil seal LH to the automatic transaxle case sub-assembly.

SST: 09649-17010

SST: 09950-70010

09951-07100

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)

NOTICE:

  • Make sure that the front drive shaft oil seal LH is installed in the correct direction.
  • Do not damage the lip of the front drive shaft oil seal LH.

*a

Depth

7. INSTALL DRIVE SHAFT BEARING BRACKET

Click here

8. INSTALL FRONT DRIVE SHAFT ASSEMBLY

Click here

    READ NEXT:

     Oil Cooler

     Components

    COMPONENTS ILLUSTRATION *1 REAR ENGINE UNDER COVER LH *2 FRONT FENDER APRON SEAL LH *3 NO. 1 ENGINE UNDER COVER *4 FRONT WHEEL OPENING EXTENSION PAD LH *5

     Removal

    REMOVAL CAUTION / NOTICE / HINT The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during tr

    SEE MORE:

     Problem Symptoms Table

    PROBLEM SYMPTOMS TABLE HINT: Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the s

     Installation

    INSTALLATION PROCEDURE 1. INSTALL KNOCK CONTROL SENSOR HINT: Perform "Inspection After Repair" after replacing a knock control sensor. Click here (a) Temporarily install the 2 knock control sensors to the cylinder block sub-assembly with the 2 bolts so that the knock control sensor insta

    © 2023-2026 Copyright www.tocamry.com