Toyota Camry (XV70): General Information
GENERAL INFORMATION
GENERAL DESCRIPTION
(a) This manual is written in accordance with SAE J2008.
(b) Repair operations can be separated mainly into the following 3 processes:
(1) Diagnosis
(2) Removing/Installing, Replacing, Disassembling/Reassembling, Checking and Adjusting
(3) Final Inspection
(c) The following procedures are omitted from this manual. However, these procedures must be performed.
(1) Use a jack or lift to perform operations.
(2) Clean all removed parts.
(3) Perform a visual check before and after performing any work.
PREPARATION
(a) Use of Special Service Tools (SST) and Special Service Materials (SSM) may be required, depending on the repair procedure. Be sure to use SST and SSM when they are required and follow the work procedure properly. A list of SST and SSM is in the "Preparation" section of this manual.
REPAIR PROCEDURES
(a) A component illustration is placed under the title where necessary.
(b) Non-reusable parts, grease application areas, precoated parts and torque specifications are noted in the component illustrations.
- The following illustration is an example.
.png)
|
*A | Example |
- | - |
|
*1 | FILTER CAP |
*2 | FLOAT |
|
*3 | RESERVOIR TANK |
*4 | SLOTTED SPRING PIN |
|
*5 | GROMMET |
*6 | CYLINDER |
|
*7 | PISTON |
*8 | PUSH ROD |
|
*9 | WASHER |
*10 | SNAP RING |
|
*11 | BOOT |
*12 | GASKET |
|
*13 | LOCK NUT |
*14 | CLEVIS PIN |
|
*15 | CLEVIS |
*16 | CLIP |
.png) |
N*m (kgf*cm, ft.*lbf): Specified torque |
● | Non-reusable part |
(c) Torque specifications, grease application areas and non-reusable parts are emphasized in the procedures.
HINT:
There are cases where such information can only be explained by using an illustration. In these cases, torque, oil and other information are described in the illustration.
(d) Only items with key points are described in the text. What to do and other details are explained using illustrations next to the text. Both the text and illustrations are accompanied by standard values and notices.
|
Illustration | What to do and where to do it |
|
Task heading | What work will be performed |
|
Explanation text |
|
(e) Illustrations of similar vehicle models are sometimes used. In these cases, minor details may be different from the actual vehicle.
(f) Procedures are presented in a step-by-step format.
SERVICE SPECIFICATIONS
(a) Specifications are presented in boldface text throughout the manual. The specifications are also found in the "Specifications" section for reference.
TERM DEFINITIONS
|
CAUTION | Possibility of injury to you or other people. |
|
NOTICE | Possibility of damage to components being repaired. |
|
HINT | Provides additional information to help you perform repairs. |
INTERNATIONAL SYSTEM OF UNITS
(a) The units used in this manual comply with the International System of Units (SI UNIT) standard. Other units from the metric system and the English systems are also provided.
- Example:
Torque:
30 N
READ NEXT:
Identification Information
Vehicle Identification And Serial NumbersVEHICLE IDENTIFICATION AND SERIAL NUMBERS
VEHICLE IDENTIFICATION NUMBER (a) The vehicle identification number is stamped on the vehicle body and on the certi
Precaution
PRECAUTION BASIC REPAIR HINT (a) HINTS ON OPERATIONS
1 Attire
Always wear a clean uniform.
A hat and safety shoes must be worn.
2
Vehicle protection Prepare a
SEE MORE:
Front Radar Sensor Optical Axis Misalignment Malfunction (C1A1100)
DESCRIPTION The millimeter wave radar sensor assembly performs self-diagnosis to check for misalignment of its beam axis. If misalignment is detected, the millimeter wave radar sensor assembly stores DTC C1A1100.
DTC No. Detection Item
DTC Detection Condition Trouble Area
C1A1
USB Device Malfunction (B1585)
DESCRIPTION This DTC is stored when a malfunction occurs in a connected device.
DTC No. Detection Item
DTC Detection Condition Trouble Area
B1585 USB Device Malfunction
When any of the following conditions is met:
A non mass-storage class or incompatible proto
