Toyota Camry owners & service manuals

Toyota Camry (XV70): Motor Control Relay Stuck ON (B2345)

Toyota Camry Repair Manual XV70 (2018-2024) / Vehicle Exterior / Sliding Roof / Convertible / Panoramic Moon Roof System / Motor Control Relay Stuck ON (B2345)

DESCRIPTION

This DTC will be stored if the operation of the sliding roof or roof sunshade is suspended and a pulse input of 10 Hz or more is detected when the motor relay is off.

Sliding Roof

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

B2345

Motor Control Relay Stuck ON

Position failure (When the sliding roof ECU (sliding roof drive gear assembly) enters fail-safe mode due to a problem with the gear position)

Sliding roof ECU (Sliding roof drive gear assembly)
Sliding Sunshade

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

B2345

Motor Control Relay Stuck ON

Position failure (When the roof sunshade ECU (sliding roof drive gear assembly) enters fail-safe mode due to a problem with the gear position)

Roof sunshade ECU (Sliding roof drive gear assembly)

CAUTION / NOTICE / HINT

NOTICE:

  • If the sliding roof ECU (sliding roof drive gear assembly) or roof sunshade ECU (sliding roof drive gear assembly) is removed and reinstalled or replaced, the sliding roof ECU (sliding roof drive gear assembly) or roof sunshade ECU (sliding roof drive gear assembly) must be initialized.

    Click here

  • DTC B2345 is stored in the sliding roof ECU (sliding roof drive gear assembly) and roof sunshade ECU (sliding roof drive gear assembly).

PROCEDURE

1.

CHECK FOR DTC

(a) Clear the DTCs.

Click here

Body Electrical > Sliding Roof > Clear DTCs Body Electrical > Sliding Sunshade > Clear DTCs

(b) Check for DTCs.

Click here

Body Electrical > Sliding Roof > Trouble Codes Body Electrical > Sliding Sunshade > Trouble Codes

OK:

DTC B2345 is not output.

OK

USE SIMULATION METHOD TO CHECK

NG

2.

CHECK DTC OUTPUT

(a) Check the parts from which this DTC has been output.

Result

Proceed to

DTC output from sliding roof ECU (sliding roof drive gear assembly)

A

DTC output from roof sunshade ECU (sliding roof drive gear assembly)

B
A

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)

B

REPLACE ROOF SUNSHADE ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)

    READ NEXT:

     Remote Control System does not Operate

    DESCRIPTION The main body ECU (multiplex network body ECU) receives remote control signals from the driver door key cylinder or wireless transmitter. Then, the main body ECU (multiplex network body EC

     Key-off Operation Function Operates even if Operating Conditions are not Satisfied

    DESCRIPTION According to the panoramic moon roof switch (roof console box sub-assembly) operation, the sliding roof ECU (sliding roof drive gear assembly) or roof sunshade ECU (sliding roof drive gear

     Panoramic Moon Roof System does not Operate

    DESCRIPTION The sliding roof ECU (sliding roof drive gear assembly) and roof sunshade ECU (sliding roof drive gear assembly) receive each other's position information from the main body ECU (multiplex

    SEE MORE:

     Reassembly

    REASSEMBLY PROCEDURE 1. INSTALL OIL PUMP ROTOR SET (a) Coat the drive rotor and driven rotor with engine oil and place them into the timing chain cover assembly with the rotor marks facing up. Check that the rotors rotate smoothly. *a Rotor Mark 2. I

     Front Axle Hub Bolt

    ComponentsCOMPONENTS ILLUSTRATION *A except 2-Pod Caliper *B for 2-Pod Caliper *1 FRONT AXLE HUB BOLT *2 FRONT DISC *3 FRONT DISC BRAKE CALIPER ASSEMBLY *4 FRONT FLEXIBLE HOSE Tightening torque for "Major areas involving basic ve

    © 2023-2026 Copyright www.tocamry.com