Toyota Camry owners & service manuals

Toyota Camry (XV70): Notification function - RSA (Road Sign Assist)

Toyota Camry Owner's Manual XV70 (2017-2024) / Driving / Using the driving support systems / Notification function - RSA (Road Sign Assist)

In the following situations, the RSA system will notify the driver.

  • When the vehicle speed exceeds the speed notification threshold of the speed limit sign displayed, the sign display will be emphasized and a buzzer will sound.
  • When the RSA system recognizes a do not enter sign and determines that your vehicle has entered a no-entry area, the displayed sign will flash and a buzzer will sound.

Depending on the situation, a notification function may not operate properly.

■Setting procedure

Vehicles with 4.2-inch multi-information display

1. Press of the meter control switches, select .

2. Press of the meter control switches, select .

3. Press of the meter control switch.

Each time is pressed, the function changes on/off.

Vehicles with 7-inch multi-information display

1. Press of the meter control switches, select .

2. Press of the meter control switches, select .

3. Press of the meter control switch.

Each time is pressed, the function changes on/off.

■Automatic turn-off of RSA sign display

In the following situations, a displayed speed limit sign and/or do not enter sign will stop being displayed automatically:

  • No sign has been recognized for a certain distance.
  • The road changes due to a left or right turn, etc.

    In the following situations, stop and yield signs will stop being displayed automatically:

  • The system determines that your vehicle has passed the sign.
  • The road changes due to a left or right turn, etc.

■Conditions in which the function may not operate or detect correctly

In the following situations, RSA does not operate normally and may not recognize signs, display the incorrect sign, etc. However, this does not indicate a malfunction.

  • The front camera is misaligned due to a strong impact being applied to the sensor, etc.
  • Dirt, snow, stickers, etc. are on the windshield near the front camera.
  • In inclement weather such as heavy rain, fog, snow or sand storms
  • Light from an oncoming vehicle, the sun, etc. enters the front camera.
  • The sign is dirty, faded, tilted or bent.
  • The contrast of electronic sign is low.
  • All or part of the sign is hidden by the leaves of a tree, a pole, etc.
  • The sign is only visible to the front camera for a short amount of time.
  • The driving scene (turning, lane change, etc.) is judged incorrectly.
  • If a sign not appropriate for the currently traveled lane, but the sign exists directly after a freeway branches, or in an adjacent lane just before merging.
  • Stickers are attached to the rear of the preceding vehicle.
  • A sign resembling a system compatible sign is recognized.
  • Side road speed signs may be detected and displayed (if positioned in sight of the front camera) while the vehicle is traveling on the main road.
  • Roundabout exit road speed signs may be detected and displayed (if positioned in sight of the front camera) while traveling on a roundabout.
  • The front of the vehicle is raised or lowered due to the carried load
  • The surrounding brightness is not sufficient or changes suddenly.
  • When a sign intended for trucks, etc. is recognized.
  • The navigation system map data is outdated.
  • The navigation system is not operating.
  • The speed information displayed on the meter and on the navigation system may be different due to the navigation system using map data.

■Speed limit sign display

If the engine switch was last turned off while a speed limit sign was displayed on the multi-information display, the same sign displays again when the engine switch is turned to ON.

■If "Road Sign Assist System Malfunction" is shown

The system may be malfunctioning. Have the vehicle inspected by your Toyota dealer.

■Customization

Some functions can be customized.

    READ NEXT:

     Dynamic radar cruise control with full-speed range

    Summary of functions In vehicle-to-vehicle distance control mode, the vehicle automatically accelerates, decelerates and stops to match the speed changes of the preceding vehicle even if the accele

     Driving in vehicle-to-vehicle distance control mode - Dynamic radar cruise control with full-speed range

    This mode employs a radar to detect the presence of vehicles up to approximately 328 ft. (100 m) ahead, determines the current vehicle-to-vehicle following distance, and operates to maintain a suitab

     Adjusting the set speed - Dynamic radar cruise control with full-speed range

    Adjusting the set speed by the switch To change the set speed, press the "+ RES" or "- SET" switch until the desired set speed is displayed. Increases the speed (Except when the vehicle h

    SEE MORE:

     Diagnostic Trouble Code Chart

    DIAGNOSTIC TROUBLE CODE CHART Navigation System DTC No. Detection Item Link B1324 Lost Communication with Meter B1325 Lost Communication with HUD B153A GVIF Disconnected (from Extension Module to H/U) B1543 Extension Mod

     Intuitive parking assist

    The distance from your vehicle to nearby objects when parallel parking or maneuvering into a garage is measured by the sensors and communicated via the multi-information display and a buzzer. Always check the surrounding area when using this system. Types of sensors Front corner sensors Fr

    © 2023-2024 Copyright www.tocamry.com