Toyota Camry owners & service manuals

Toyota Camry (XV70): Removal

Toyota Camry Repair Manual XV70 (2018-2024) / Suspension / Rear Suspension / Rear Suspension Member (for Awd) / Removal

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear suspension member sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

Rear wheel alignment adjustment
  • Perform "Reset Memory"
  • Perform acceleration sensor zero point calibration and system information memorization
  • VSC disabled or malfunctioning
  • DTCs are output
  • Slip indicator light illuminated
  • ABS warning light illuminated

Suspension, tires, etc.

(The vehicle height changes because of suspension or tire replacement)

Rear television camera assembly optical axis (Back camera position setting)

Parking assist monitor system

for Initialization

for Calibration
  • Television camera controller initialization
  • Adjust steering angle
  • Rear television camera assembly optical axis (Back camera position setting)

Panoramic view monitor system

for Initialization

for Calibration
  • Replacement of air fuel ratio sensor
  • Gas leak from exhaust system is repaired

Inspection After Repair
  • Poor idle, etc.
  • Engine start function, etc.

CAUTION:

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.

PROCEDURE

1. REMOVE REAR DIFFERENTIAL CARRIER ASSEMBLY

Click here

2. REMOVE REAR NO. 1 DIFFERENTIAL MOUNT CUSHION

Click here

3. REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

Click here

4. REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.

5. REMOVE SPARE WHEEL COVER ASSEMBLY

Click here

6. REMOVE REAR SEAT CUSHION ASSEMBLY

Click here

7. REMOVE REAR SEAT CUSHION LOCK HOOK

Click here

8. REMOVE REAR SEATBACK ASSEMBLY LH

Click here

9. REMOVE REAR SEATBACK ASSEMBLY RH

Click here

10. REMOVE LUGGAGE COMPARTMENT TRIM INNER PAD

Click here

11. REMOVE REAR SUSPENSION MEMBER SUB-ASSEMBLY

(a) Disconnect the connector and disengage the clamp.

(b) Remove the grommet of the wire harness and pass the connector through the hole to the outside of the vehicle.

(c) Using an engine lifter and 4 attachments or equivalent tools, support the rear suspension member sub-assembly as shown in the illustration.

  • The rear suspension member sub-assembly is a very heavy component. Make sure that it is supported securely.
  • If the rear suspension member sub-assembly is not securely supported, it may drop, resulting in serious injury.

NOTICE:

Use attachments or equivalent tools to keep the rear suspension member sub-assembly level.

*a

Engine Lifter

*b

Attachment

Attachment Placement Location

(d) Remove the 2 bolts, 6 nuts, 2 rear suspension member lower stoppers, rear suspension member lower brace LH and rear suspension member lower brace RH.

(e) Slowly lower the rear suspension member sub-assembly.

NOTICE:

When lowering the rear suspension member sub-assembly, be careful not to damage the vehicle body or other components installed to the vehicle.

(f) Remove the 4 rear suspension member cushions from the rear suspension member sub-assembly.

HINT:

Make sure to place an identification mark on the rear suspension member cushion so that they can be reinstalled to their original positions.

12. REMOVE WIRE HARNESS

(a) Disengage the 2 clamps and remove the wire harness from the rear suspension member sub-assembly.

13. REMOVE REAR UPPER CONTROL ARM ASSEMBLY LH

Click here

14. REMOVE REAR UPPER CONTROL ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.

15. REMOVE REAR SUSPENSION MEMBER FRONT BODY MOUNTING CUSHION (for LH Side)

(a) Using a chisel and hammer, bend the 2 portions of the rear suspension member front body mounting cushion rib.

NOTICE:

Make sure to bend the 2 portions of the cushion rib until the claws of SST can fit securely.

*a

Bend Portion

(b) Apply lubricant to the contact surfaces of the rear suspension member front body mounting cushion.

(c) Install SST as shown in the illustration.

SST: 09830-10010

09830-01010

09830-01040

09830-01050

SST: 09950-40011

09951-04010

09952-04010

09954-04010

09955-04061

09958-04011

NOTICE:

Apply molybdenum grease to the threads and tip of the SST center bolt before use.

(d) Using SST, remove the rear suspension member front body mounting cushion while applying lubricant into the clearance between the rear suspension member front body mounting cushion and the rear suspension member sub-assembly.

SST: 09830-10010

09830-01010

09830-01040

09830-01050

SST: 09950-40011

09951-04010

09952-04010

09954-04010

09955-04061

09958-04011

NOTICE:

  • Set the claws of SST into the rear suspension member sub-assembly securely as shown in the illustration.
  • Tighten SST slowly and evenly.
  • Be careful as the rear suspension member front body mounting cushion may fly out.
  • The rear suspension member front body mounting cushion cannot be reused.

*a

Hold

Turn

(e) Remove SST and the rear suspension member front body mounting cushion from the rear suspension member sub-assembly.

16. REMOVE REAR SUSPENSION MEMBER FRONT BODY MOUNTING CUSHION (for RH Side)

HINT:

Perform the same procedure as for the LH side.

17. REMOVE REAR SUSPENSION MEMBER REAR BODY MOUNT CUSHION LH

(a) Install SST as shown in the illustration.

SST: 09950-00020

SST: 09950-00030

SST: 09950-60011

09951-00330

NOTICE:

Apply molybdenum grease to the threads and tip of the SST center bolt before use.

(b) Using SST, remove the rear suspension member rear body mount cushion LH while applying lubricant into the clearance between the rear suspension member rear body mount cushion LH and the rear suspension member sub-assembly.

SST: 09950-00020

SST: 09950-00030

SST: 09950-60011

09951-00330

NOTICE:

  • Tighten SST slowly and evenly.
  • Be careful as the rear suspension member rear body mount cushion LH may fly out.
  • The rear suspension member rear body mount cushion LH cannot be reused.

*a

Hold

Turn

(c) Remove SST and the rear suspension member rear body mount cushion LH from the rear suspension member sub-assembly.

18. REMOVE REAR SUSPENSION MEMBER REAR BODY MOUNT CUSHION RH

HINT:

Perform the same procedure as for the LH side.

19. REMOVE HOLE PLUG

(a) Remove the 10 hole plugs from the rear suspension member sub-assembly.

HINT:

There are 2 different shapes of hole plug.

    READ NEXT:

    SEE MORE:

     Components

    COMPONENTS ILLUSTRATION *A for A25A-FKS - - *1 NO. 1 VACUUM HOSE CONNECTOR *2 UNION TO CHECK VALVE HOSE *3 VACUUM HOSE *4 CLIP ILLUSTRATION *A for 2GR-FKS - - *1 FRONT CENTER UPPER SUSPENSION BRACE SUB-ASSEMBLY

     Blind Spot Monitor Slave Module (C1AB7)

    DESCRIPTION This DTC is stored when the blind spot monitor sensor LH detects an internal malfunction. DTC No. Detection Item DTC Detection Condition Trouble Area C1AB7 Blind Spot Monitor Slave Module The blind spot monitor sensor LH (slave) detects an internal malfunct

    © 2023-2025 Copyright www.tocamry.com