Toyota Camry owners & service manuals

Toyota Camry (XV70): Data List / Active Test

Toyota Camry Repair Manual XV70 (2018-2024) / Drivetrain / Ua80e (automatic Transmission / Transaxle) / Automatic Transaxle System / Data List / Active Test

DATA LIST / ACTIVE TEST

DATA LIST

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

(a) Warm up the engine.

(b) Turn the engine switch off.

(c) Connect the Techstream to the DLC3.

(d) Turn the engine switch on (IG).

(e) Turn the Techstream on.

(f) Enter the following menus: Powertrain / Transmission / Data List.

(g) Read the Data List according to the display on the Techstream.

Powertrain > Transmission > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Total Distance Traveled

Total distance traveled

Min.: 0

Max.: 16777215

-

-

Total Distance Traveled - Unit

Unit for Total Distance Traveled

km or mile

-

-

Vehicle Speed

Vehicle speed

Min.: 0 km/h (0 mph)

Max.: 255 km/h (158 mph)

Actual vehicle speed
  • This is the current vehicle speed.
  • The vehicle speed is detected using the wheel speed sensors.
    • Vehicle speed data is delayed when it is displayed. Therefore, even if the vehicle speed listed in the freeze frame data is 0 km/h (0 mph), this does not always mean that the malfunction occurred when the vehicle was stopped.

Engine Speed

Engine Speed

Min.: 0 rpm

Max.: 16383 rpm

650 to 750 rpm: Engine idling (shift lever in N, engine warmed up and A/C off)

When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed.

Calculate Load

Load calculated by ECM

Min.: 0%

Max.: 100%

-
  • This is the engine load calculated based on the estimated intake manifold pressure.
  • Calculate Load = Actual intake manifold pressure / maximum intake manifold pressure x 100 (%)

    (For example, when the actual intake manifold pressure is the same as ambient pressure, Calculate Load is 100%.)

Coolant Temperature

Engine coolant temperature

Min.: -40

    READ NEXT:

     Diagnostic Trouble Code Chart

    DIAGNOSTIC TROUBLE CODE CHART Automatic Transaxle System DTC No. Detection Item MIL Memory Note Link P050031 Vehicle Speed Sensor "A" No Signal Comes on DTC sto

     Vehicle Control History

    VEHICLE CONTROL HISTORY VEHICLE CONTROL HISTORY HINT: A part of the control history can be confirmed using the vehicle control history. Click here

     System Voltage Circuit Short to Ground or Open (P056014)

    DESCRIPTION The battery supplies electricity to the ECM even when the engine switch is off. This power allows the ECM to store data such as DTC history and freeze frame data. If the battery voltage fa

    SEE MORE:

     Operation Check

    OPERATION CHECK CHECK NAVIGATION SYSTEM NORMAL CONDITION (a) If the cause of a symptom is any of the following, the corresponding symptom is normal; it is not due to a malfunction. Symptom Answer A longer route than expected is chosen. Depending on the road conditions, the na

     Installation

    INSTALLATION PROCEDURE 1. INSTALL ENGINE OIL PRESSURE SWITCH ASSEMBLY (a) Apply adhesive to 2 or 3 threads of the engine oil pressure switch assembly. Adhesive: Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent NOTICE: Do not apply adhesive to the oil inlet port of the e

    © 2023-2026 Copyright www.tocamry.com