Toyota Camry owners & service manuals

Toyota Camry (XV70): Data List / Active Test

DATA LIST / ACTIVE TEST

DATA LIST

HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:

In the following table, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Main Body / Data List.

(e) Read the Data List according to the display on the Techstream.

Body Electrical > Main Body > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Key Unlock Warning SW

Unlock warning switch signal

OFF or ON

OFF: No key in ignition key cylinder

ON: Key in ignition key cylinder

-

FL Door Courtesy SW

Front door courtesy light switch assembly (for LH) signal

OFF or ON

OFF: Front door LH closed

ON: Front door LH open

-

ACTIVE TEST

HINT:

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Combination Meter/ Active Test.

(e) Perform the Active Test according to the display on the Techstream.

Body Electrical > Combination Meter > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

Buzzer Operation (800Hz, Vol L, W/ Damping)

Combination meter buzzer

  • Frequency: 800Hz
  • Volume: Large
  • Fading tone

ON

-

Buzzer Operation (800Hz, Vol L, W/O Damping)

Combination meter buzzer

  • Frequency: 800Hz
  • Volume: Large
  • Continuous tone

ON

-

Buzzer Operation (800Hz, Vol S, W/ Damping)

Combination meter buzzer

  • Frequency: 800Hz
  • Volume: Small
  • Fading tone

ON

-

Buzzer Operation (800Hz, Vol S, W/O Damping)

Combination meter buzzer

  • Frequency: 800Hz
  • Volume: Small
  • Continuous tone

ON

-

    READ NEXT:

     Key Reminder Buzzer does not Sound

    DESCRIPTION The key reminder warning buzzer sounds when the driver door is opened while the ignition switch is off or ACC. The key reminder warning buzzer is activated when the main body ECU (multiple

     Luggage Compartment Door Lock

    ComponentsCOMPONENTS ILLUSTRATION *1 LUGGAGE COMPARTMENT DOOR COVER *2 LUGGAGE COMPARTMENT DOOR INSIDE HANDLE *3 LUGGAGE COMPARTMENT DOOR LOCK ASSEMBLY *4 LUGGAGE DOOR

     Power Door Lock Control System

    SEE MORE:

     Removal

    REMOVAL CAUTION / NOTICE / HINT The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel injector assembly removal/installation are shown below. Necessary Procedures After Parts Removed/

     Blind Spot Monitor Master Module (C1AB6)

    DESCRIPTION This DTC is stored when the blind spot monitor sensor RH detects an internal malfunction. DTC No. Detection Item DTC Detection Condition Trouble Area C1AB6 Blind Spot Monitor Master Module The blind spot monitor sensor RH (master) detects an internal malfun

    © 2023-2026 Copyright www.tocamry.com