Toyota Camry owners & service manuals

Toyota Camry (XV70): Freeze Frame Data

FREEZE FRAME DATA

FREEZE FRAME DATA/INFORMATION

(a) Using the Techstream, check the vehicle condition (ECU, sensor) when the brake system operates or a DTC is output.

CHECK FREEZE FRAME DATA AND INFORMATION WHEN DTC WAS STORED

(a) Freeze Frame Data is stored when a DTC is output.

(b) Once Freeze Frame Data is stored when a DTC is output, it is not updated or cleared until the DTC is cleared.

(c) Check the corresponding freeze frame data and detailed information of the DTC.

(1) Turn the ignition switch off.

(2) Connect the Techstream to the DLC3.

(3) Turn the ignition switch to ON.

(4) Turn the Techstream on.

(5) Enter the following menus: Chassis / Brake / Trouble Codes.

Chassis > Brake > Trouble Codes

(6) Select a DTC to display the Freeze Frame Data.

(7) Check the Freeze Frame Data for the output DTC.

Chassis > Brake

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Total Distance Traveled - Unit

Total Distance Traveled unit

km / mile

-

-

Total Distance Traveled

Total distance traveled

Min.: 0, Max.: 16777215

-

-

IG1 Voltage Value

IG1 terminal voltage value (value detected by ECU)

Min.: 0.0 V, Max.: 25.5 V

Ignition switch ON: 11.0 to 14.0 V

Changes in proportion to battery voltage

BS1 Voltage Value

+BS terminal voltage value (value detected by ECU)

Min.: 0.0 V, Max.: 25.5 V

Ignition switch ON: 11.0 to 14.0 V

Changes in proportion to battery voltage

HINT:

This is the voltage detected at terminal +BS (which supplies power to each solenoid) of the skid control ECU (brake actuator assembly)

Motor Power Supply Voltage

+BM terminal voltage value (value detected by ECU)

Min.: 0.0 V, Max.: 25.5 V

Ignition switch ON: 11.0 to 14.0 V

Changes in proportion to battery voltage

HINT:

This is the voltage detected at terminal +BM (which supplies power to the ABS motor) of the skid control ECU (brake actuator assembly)

FR Wheel Speed

Front wheel speed sensor RH reading

Min.: 0.0 km/h (0 mph), Max.: 6553.5 km/h (4072 mph)

Vehicle stopped: 0.0 km/h (0.0 mph)

When driving at constant speed: No large fluctuations

FL Wheel Speed

Front wheel speed sensor LH reading

Min.: 0.0 km/h (0 mph), Max.: 6553.5 km/h (4072 mph)

Vehicle stopped: 0.0 km/h (0.0 mph)

When driving at constant speed: No large fluctuations

RR Wheel Speed

Rear wheel speed sensor RH reading

Min.: 0.0 km/h (0 mph), Max.: 6553.5 km/h (4072 mph)

Vehicle stopped: 0.0 km/h (0.0 mph)

When driving at constant speed: No large fluctuations

RL Wheel Speed

Rear wheel speed sensor LH reading

Min.: 0.0 km/h (0 mph), Max.: 6553.5 km/h (4072 mph)

Vehicle stopped: 0.0 km/h (0.0 mph)

When driving at constant speed: No large fluctuations

Master Cylinder Sensor 1

Master cylinder pressure sensor pressure (value detected by ECU)

Min.: -1.00 MPa, Max.: 23.99 MPa

Brake pedal released: -1.00 to 0.00 MPa

Reading increases when brake pedal is depressed

M/C Sensor Grade

Master cylinder pressure sensor change (value detected by ECU)

Min.: -30 MPa/s, Max.: 225 MPa/s

Brake pedal released or pedal held at constant position: 0 MPa/s

When brake pedal is being operated: Changes in proportion with the pedal movement speed

Lateral G

Lateral G

Min.: -25.105 m/s2, Max.: 24.908 m/s2

Turning right: -25.105 to 0.000 m/s2

Turning left: 0.000 to 24.908 m/s2

During turning: Changes in proportion with lateral acceleration

Forward and Rearward G

Forward and rearward G

Min.: -25.105 m/s2, Max.: 24.908 m/s2

During deceleration: -25.105 to 0.000 m/s2

During acceleration: 0.000 to 24.908 m/s2

During acceleration/deceleration: Changes in proportion with acceleration

Yaw Rate Sensor Value

Yaw rate sensor

Min.: -128

    READ NEXT:

     Fail-safe Chart

    FAIL-SAFE CHART FAIL-SAFE CHART (a) When the skid control ECU (brake actuator assembly) detects a solenoid valve malfunction or abnormal signal from a sensor, the brake actuator assembly cuts power an

     Data List / Active Test

    DATA LIST / ACTIVE TEST DATA LIST NOTICE: In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a

     Diagnostic Trouble Code Chart

    DIAGNOSTIC TROUBLE CODE CHART Vehicle Stability Control System DTC No. Detection Item Link C00631C Yaw Rate Sensor Circuit Voltage Out of Range C00631F Yaw Ra

    SEE MORE:

     Dtc Check / Clear

    DTC CHECK / CLEAR CHECK DTC (CHECK USING TECHSTREAM) (a) Connect the Techstream to the DLC3. (b) Turn the engine switch on (IG) and wait for 90 seconds. (c) Turn the Techstream on. (d) Enter the following menus: Body Electrical / Navigation System / Trouble Codes. Body Electrical > Navigation

     Installation

    INSTALLATION PROCEDURE 1. PRECAUTION (w/o Navigation System) NOTICE: When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occurs: A communicatio

    © 2023-2024 Copyright www.tocamry.com