Toyota Camry (XV70): Installation
INSTALLATION
PROCEDURE
1. INSTALL DCM (TELEMATICS TRANSCEIVER)
2. INSTALL NAVIGATION ECU (w/ Navigation System)
3. INSTALL NO. 1 TELEPHONE BRACKET
(a) w/o Navigation System:
(1) Install the No. 1 telephone bracket with the screw.
(b) w/ Navigation System:
(1) Install the No. 1 telephone bracket with the 3 screws.
4. INSTALL NO. 2 TELEPHONE BRACKET
(a) w/o Navigation System:
(1) Install the No. 2 telephone bracket with the screw.
(b) w/ Navigation System:
(1) Install the No. 2 telephone bracket with the 3 screws.
5. INSTALL ANTENNA CORD SUB-ASSEMBLY
(a) w/o Navigation System:
(1) Engage the clamp to install the antenna cord sub-assembly.
(2) Connect the 3 connectors.
(b) w/ Navigation System:
(1) Engage the clamp to install the antenna cord sub-assembly.
(2) Connect the 4 connectors.
6. INSTALL DCM (TELEMATICS TRANSCEIVER) WITH BRACKET
(a) Connect each connector.
(b) Engage the clamp.
(c) Engage the 3 guides.
(d) Install the DCM (telematics transceiver) with bracket with the 3 bolts.
(e) Connect each connector.
7. INSTALL REAR UPPER CONSOLE PANEL SUB-ASSEMBLY
Click here .gif)
8. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY
for UB80E:
Click here
for UA80E:
Click here
for UB80F:
Click here
9. INSTALL SHIFT LOCK RELEASE BUTTON COVER
for UB80E:
Click here
for UA80E:
Click here
for UB80F:
Click here
10. INSTALL LOWER CENTER INSTRUMENT PANEL FINISH PANEL
Click here
11. INSTALL INSTRUMENT PANEL FINISH PLATE GARNISH
Click here
12. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY
Click here
13. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (for 7 Inch Display)
Click here
14. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (for 9 Inch Display)
Click here
15. INSTALL AIR CONDITIONING CONTROL ASSEMBLY
Click here
16. PERFORM DCM ACTIVATION
HINT:
After replacing the DCM (telematics transceiver), make sure to perform DCM activation.
Click here
17. PERFORM REGISTRATION
(a) for Toyota Entune Remote Connect Compatible Type:
(1) w/ Smart Key System:
HINT:
After replacing the DCM (telematics transceiver), make sure to perform code registration (Smart key System (for Start Function)).
Click here
(2) w/o Smart Key System:
HINT:
After replacing the DCM (telematics transceiver), make sure to perform code registration (Immobiliser system (w/o Smart Key System)).
Click here
READ NEXT:
Manual(sos)switch
ComponentsCOMPONENTS ILLUSTRATION
*A for Normal Roof
*B except Normal Roof
*1 MANUAL (SOS) SWITCH (ROOF CONSOLE BOX ASSEMBLY)
- - RemovalREMOVAL PROCEDURE
1.
Precaution
PRECAUTION PRECAUTION FOR DISCONNECTING CABLE FROM NEGATIVE BATTERY TERMINAL
NOTICE: When disconnecting the cable from the negative (-) battery terminal, initialize the following systems after the t
SEE MORE:
Disposal
DISPOSAL PROCEDURE 1. DISPOSE OF LUGGAGE COMPARTMENT DOOR SUPPORT ASSEMBLY
(a) Secure the luggage compartment door support assembly horizontally in a vise with the piston rod pulled out.
(b) Wearing safety glasses, gradually cut a part within the area (a) shown in the
SRS airbag system components
Front impact sensors
Front passenger occupant
classification system (ECU
and sensors)
Knee airbags
Side impact sensors (front
doors)
Side impact sensors (front)
Front passenger airbag
Front side airbags
Curtain shield airbags
Rear side airbags
"AIRBAG ON" and "AIRBAG
O
