Toyota Camry owners & service manuals

Toyota Camry (XV70): Master Module Horizontal Axis Misalignment (C1AC1)

DESCRIPTION

This DTC is stored when the angle of the blind spot monitor sensor RH deviates more than the allowable range from the horizontal axis.

HINT:

  • If a drum tester such as a speedometer tester, brake/speedometer combination tester or chassis dynamometer is used with the blind spot monitor system on, the blind spot monitor sensor may store this DTC by mistake.
  • When mud, snow, ice, a sticker, etc. is covering the sensor or its surrounding area on the rear bumper, the blind spot monitor sensor may store this DTC by mistake.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

C1AC1

Master Module Horizontal Axis Misalignment

When the blind spot monitor sensor deviates 5 degrees or more from the horizontal axis when the system is activated

Blind spot monitor sensor RH

CAUTION / NOTICE / HINT

NOTICE:

  • When checking for DTCs, make sure that the blind spot monitor system is turned on.
  • If the bumper is damaged or the vehicle has a history of body repair, there is a possibility that the installation area of the blind spot monitor sensor may be deformed and the blind spot monitor sensor system may not operate correctly, so visually inspect the blind spot monitor sensor installation area (frame, stud bolt) to make sure it is not dented or bent.

    Click here

    If the visual inspection finds a problem, check the installation condition of the blind spot monitor sensor, and adjust the installation position of the blind spot monitor sensor as necessary.

PROCEDURE

1.

CHECK VEHICLE CONDITION

(a) Check the condition of the rear bumper around the blind spot monitor sensors.

HINT:

When mud, snow, ice, a sticker, etc. is covering the sensor or its surrounding area on the rear bumper, the blind spot monitor sensor may store this DTC by mistake.

Result

Proceed to

A sticker, mud, snow, ice, etc. is covering the sensor or surrounding area on the rear bumper.

A

There are scratches or dents on the rear bumper around the sensors.

B

No abnormalities.

B

GO TO STEP 3

A

2.

PERFORM BEAM AXIS CONFIRMATION

(a) Clean the rear bumper.

(b) Perform Blind Spot Monitor Beam Axis Confirmation using the Techstream.

Click here

Body Electrical > Blind Spot Monitor Master > Utility

Tester Display

BSM Master Beam Axis Display

Body Electrical > Blind Spot Monitor Master > Utility

Tester Display

BSM Master Beam Axis Adjustment

OK

END

NG

REPLACE BLIND SPOT MONITOR SENSOR RH

Click here

NOTICE:

Before replacing the blind spot monitor sensor RH, visually check for damage to the stud bolts or area surrounding the blind spot monitor sensor RH.

If there is any damage to the stud bolts or area surrounding the blind spot monitor sensor RH, perform Blind Spot Monitor Sensor Installation Condition Inspection and adjust according to the result.

Click here

3.

CHECK INSTALLATION CONDITION

(a) Check the installation condition of the blind spot monitor sensor RH.

Click here

HINT:

Take the appropriate action in accordance with the result.

NEXT

4.

PERFORM BEAM AXIS CONFIRMATION

(a) Install the rear bumper.

Click here

(b) Perform Blind Spot Monitor Beam Axis Confirmation using the Techstream.

Click here

Body Electrical > Blind Spot Monitor Master > Utility

Tester Display

BSM Master Beam Axis Display

Body Electrical > Blind Spot Monitor Master > Utility

Tester Display

BSM Master Beam Axis Adjustment

OK

END

NG

REPLACE BLIND SPOT MONITOR SENSOR RH

    READ NEXT:

     Slave Module Horizontal Axis Misalignment (C1AC2)

    DESCRIPTION This DTC is stored when the angle of the blind spot monitor sensor LH deviates more than the allowable range from the horizontal axis. HINT: If a drum tester such as a speedometer te

     Lost Communication with ECM / PCM "A" (U0100,U0125,U0126,U0129,U0142)

    DESCRIPTION These DTCs are stored if there is a malfunction in the CAN communication system connected to the blind spot monitor sensor. HINT: If CAN communication system DTCs are stored, they may al

     Lost Communication with Blind Spot Monitor Slave Module (U0232)

    DESCRIPTION This DTC is stored when the blind spot monitor sensor RH judges that there is a communication problem with the blind spot monitor sensor LH. DTC No. Detection Item DTC Detecti

    SEE MORE:

     RR Speed Sensor Wrong Installation (X0454)

    DESCRIPTION Code Tester Display Measurement Item Trouble Area X0454 RR Speed Sensor Wrong Installation History of rear speed sensor RH being installed incorrectly Rear Speed Sensor RH PROCEDURE 1. CHECK FOR DTCs (HEALTH CHECK) (a) Perform the Hea

     Components

    COMPONENTS ILLUSTRATION *1 FRONT DOOR OPENING TRIM WEATHERSTRIP *2 FRONT NO. 2 SPEAKER ASSEMBLY *3 FRONT PILLAR GARNISH *4 NO. 1 INSTRUMENT PANEL SPEAKER PANEL *5 CLIP - - ● Non-reusable part - -

    © 2023-2024 Copyright www.tocamry.com