Toyota Camry owners & service manuals

Toyota Camry (XV70): Rear Television Camera Communication Stop Mode

Toyota Camry Repair Manual XV70 (2018-2024) / Power Source, Network / Networking / Can Communication System / Rear Television Camera Communication Stop Mode

DESCRIPTION

Detection Item

Symptom

Trouble Area

Rear Television Camera Communication Stop Mode

Any of the following conditions are met:

  • Communication stop for "Parking Assist Monitor System / Rear Camera" is indicated on the "Communication Bus Check" screen of the Techstream.

    Click here

  • Communication stop history for "Parking Assist Monitor System / Rear Camera" is indicated on the "Communication Bus Check (Detail)" screen of the Techstream. (The Lost Communication Time value for "Parking Assist Monitor System / Rear Camera" is 6 or more.)

    Click here

  • Communication system DTCs (DTCs that start with U) that correspond to "Rear Television Camera Communication Stop Mode" in "DTC Combination Table" are output.

    Click here

  • Rear television camera assembly branch line or connector
  • Power source circuit of rear television camera assembly
  • Rear television camera assembly ground circuit
  • Rear television camera assembly

WIRING DIAGRAM

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.

NOTICE:

  • Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

    Click here

  • Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
  • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  • After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

    DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

  • After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

    Click here

  • Inspect the fuses for circuits related to this system before performing the following procedure.

HINT:

  • Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
  • When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.

PROCEDURE

1.

CHECK FOR OPEN IN CAN BUS LINES (REAR TELEVISION CAMERA ASSEMBLY BRANCH LINE)

(a) Disconnect the cable from the negative (-) battery terminal.

(b) Disconnect the m1 rear television camera assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

m1-4 (CANH) - m1-1 (CANL)

Cable disconnected from negative (-) battery terminal

54 to 69 Ω

*a

Front view of wire harness connector

(to Rear Television Camera Assembly)
NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (REAR TELEVISION CAMERA ASSEMBLY)
OK

2.

CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

m1-5 (CGND) - Body ground

Cable disconnected from negative (-) battery terminal

Below 1 Ω

*a

Front view of wire harness connector

(to Rear Television Camera Assembly)

(b) Reconnect the cable to the negative (-) battery terminal.

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

m1-6 (CB+) - Body ground

Ignition switch ACC

11 to 14 V
OK

REPLACE REAR TELEVISION CAMERA ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

    READ NEXT:

     Restraints Occupant Classification System Module Communication Stop Mode

    DESCRIPTION Detection Item Symptom Trouble Area Restraints Occupant Classification System Module Communication Stop Mode Any of the following conditions are met: Commun

     Open in Bus 1 Main Bus Line

    DESCRIPTION There may be an open circuit in one of the CAN main bus lines when the resistance between terminals 23 (CA1H) and 8 (CA1L) of the central gateway ECU (network gateway ECU) is 70 Ω or

     Check Bus 1 Lines for Short Circuit

    DESCRIPTION There may be a short circuit between the CAN main bus lines and/or CAN branch lines when the resistance between terminals 23 (CA1H) and 8 (CA1L) of the central gateway ECU (network gateway

    SEE MORE:

     AWD Warning does not Come ON

    DESCRIPTION Refer to "4WD Warning Remains ON". Click here WIRING DIAGRAM Refer to "4WD Warning Remains ON". Click here CAUTION / NOTICE / HINT Refer to "4WD Warning Remains ON". Click here PROCEDURE 1. CHECK HARNESS AND CONNECTOR (a) Check that there is no looseness at

     Installation

    INSTALLATION PROCEDURE 1. INSTALL TIMING CHAIN CASE OIL SEAL (a) Apply MP grease to the lip of a new timing chain case oil seal. *a Oil Seal Protrusion Height (b) Using SST and a hammer, tap in the timing chain case oil seal until its surface is flus

    © 2023-2026 Copyright www.tocamry.com