Toyota Camry (XV70): Right Front Wheel ABS Hold Solenoid Control Circuit Short to Battery (C12BB12,...,C12C649)
DESCRIPTION
The ABS solenoid relay and solenoid valves are built into the brake actuator assembly.
The front solenoid valve RH controls the brake fluid pressure of the front wheel cylinder RH of the vehicle.
When this DTC is stored, the fail-safe function operates and the ABS solenoid relay is turned off to prevent the solenoid valves from operating.
|
DTC No. | Detection Item |
DTC Detection Condition | Trouble Area |
|---|---|---|---|
|
C12BB12 | Right Front Wheel ABS Hold Solenoid Control Circuit Short to Battery |
A short to +B in the solenoid circuit is detected during the self test. |
Skid control ECU (brake actuator assembly) |
|
C12BB14 | Right Front Wheel ABS Hold Solenoid Control Circuit Short to Ground or Open |
An open or short in the solenoid circuit is detected during the self test. |
Skid control ECU (brake actuator assembly) |
|
C12BB1C | Right Front Wheel ABS Hold Solenoid Control Circuit Voltage Out of Range |
| Skid control ECU (brake actuator assembly) |
|
C12BB1E | Right Front Wheel ABS Hold Solenoid Control Circuit Resistance Out of Range |
An abnormal resistance in the solenoid circuit is detected during the self test. |
Skid control ECU (brake actuator assembly) |
|
C12BB49 | Right Front Wheel ABS Hold Solenoid Control Internal Electronic Failure |
An internal malfunction in the solenoid circuit is detected during the self test. |
Skid control ECU (brake actuator assembly) |
|
C12C612 | Right Front Wheel ABS Release Solenoid Control Circuit Short to Battery |
A short to +B in the solenoid circuit is detected during the self test. |
Skid control ECU (brake actuator assembly) |
|
C12C614 | Right Front Wheel ABS Release Solenoid Control Circuit Short to Ground or Open |
An open or short in the solenoid circuit is detected during the self test. |
Skid control ECU (brake actuator assembly) |
|
C12C61C | Right Front Wheel ABS Release Solenoid Control Circuit Voltage Out of Range |
| Skid control ECU (brake actuator assembly) |
|
C12C61E | Right Front Wheel ABS Release Solenoid Control Circuit Resistance Out of Range |
An abnormal resistance in the solenoid circuit is detected during the self test. |
Skid control ECU (brake actuator assembly) |
|
C12C649 | Right Front Wheel ABS Release Solenoid Control Internal Electronic Failure |
An internal malfunction in the solenoid circuit is detected during the self test. |
Skid control ECU (brake actuator assembly) |
|
Vehicle Condition | |||
|---|---|---|---|
|
Pattern 1 | Pattern 2 | ||
|
Diagnosis Condition | - |
- | - |
|
Malfunction Status | An open in the solenoid circuit is detected during the self test. |
○ | - |
|
A short in the solenoid circuit is detected during the self test. |
- | ○ | |
|
Detection Time | - |
- | |
|
Number of Trips | 1 trip |
1 trip | |
HINT:
DTC will be output when conditions for either of the patterns in the table above are met.
DTC Detection Conditions: C12BB1C|
Vehicle Condition | |||
|---|---|---|---|
|
Pattern 1 | Pattern 2 | ||
|
Diagnosis Condition | - |
- | - |
|
Malfunction Status | A current leak in the solenoid circuit is detected during the self test. |
○ | - |
|
The solenoid operation request signal and solenoid operation feedback signal do not match for a certain period of time. |
- | ○ | |
|
Detection Time | - |
- | |
|
Number of Trips | 1 trip |
1 trip | |
HINT:
DTC will be output when conditions for either of the patterns in the table above are met.
DTC Detection Conditions: C12C614|
Vehicle Condition | |||
|---|---|---|---|
|
Pattern 1 | Pattern 2 | ||
|
Diagnosis Condition | - |
- | - |
|
Malfunction Status | An open in the solenoid circuit is detected during the self test. |
○ | - |
|
A short in the solenoid circuit is detected during the self test. |
- | ○ | |
|
Detection Time | - |
- | |
|
Number of Trips | 1 trip |
1 trip | |
HINT:
DTC will be output when conditions for either of the patterns in the table above are met.
DTC Detection Conditions: C12C61C|
Vehicle Condition | |||
|---|---|---|---|
|
Pattern 1 | Pattern 2 | ||
|
Diagnosis Condition | - |
- | - |
|
Malfunction Status | A current leak in the solenoid circuit is detected during the self test. |
○ | - |
|
The solenoid operation request signal and solenoid operation feedback signal do not match for a certain period of time. |
- | ○ | |
|
Detection Time | - |
- | |
|
Number of Trips | 1 trip |
1 trip | |
HINT:
DTC will be output when conditions for either of the patterns in the table above are met.
CAUTION / NOTICE / HINT
NOTICE:
After replacing the skid control ECU (brake actuator assembly), perform acceleration sensor zero point calibration and system information memorization.
Click here .gif)
PROCEDURE
| 1. |
REPLACE BRAKE ACTUATOR ASSEMBLY |
(a) Replace the skid control ECU (brake actuator assembly).
Click here
| NEXT | .gif) | END |
READ NEXT:
Left Rear Wheel ABS Hold Solenoid Control Circuit Short to Battery (C12D112,...,C12DC49)
DESCRIPTION The ABS solenoid relay and solenoid valves are built into the brake actuator assembly.
The rear solenoid valve LH controls the brake fluid pressure of the rear wheel cylinder LH of the v
Right Rear Wheel ABS Hold Solenoid Control Circuit Short to Battery (C12E712,...,C12F249)
DESCRIPTION The ABS solenoid relay and solenoid valves are built into the brake actuator assembly.
The rear solenoid valve RH controls the brake fluid pressure of the rear wheel cylinder RH of the v
Brake System Control Module "A" System Voltage System Voltage Low (C137BA2)
DESCRIPTION If a malfunction is detected in the power supply circuit, the skid control ECU (brake actuator assembly) stores this DTC and the fail-safe function prohibits ABS operation.
This DTC is s
SEE MORE:
Data Signal Circuit between Radio Receiver and Stereo Jack Adapter
DESCRIPTION The No. 1 stereo jack adapter assembly sends the sound data signal or image data signal from a USB device to the radio and display receiver assembly via this circuit. WIRING DIAGRAM
PROCEDURE
1.
CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 1 STEREO
Removal
REMOVAL CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during park/neutral position switch assembly removal/installation are shown below. Necessary Procedures After
