Toyota Camry owners & service manuals

Toyota Camry (XV70): Software Incompatibility with Body Control Module "B" (U1331)

Toyota Camry Repair Manual XV70 (2018-2024) / Audio, Visual, Telematics / Park Assist / Monitoring / Blind Spot Monitor System / Software Incompatibility with Body Control Module "B" (U1331)

DESCRIPTION

This DTC is stored when the destination information of the main body ECU (multiplex network body ECU) does not match that of the blind spot monitor sensors.

Blind Spot Monitor Master

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

U1331

Software Incompatibility with Body Control Module "B"

Destination information of the main body ECU and blind spot monitor sensor do not match
  • Main body ECU (multiplex network body ECU)
  • Blind spot monitor sensor RH
Blind Spot Monitor Slave

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

U1331

Software Incompatibility with Body Control Module "B"

Destination information of the main body ECU and blind spot monitor sensor do not match
  • Main body ECU (multiplex network body ECU)
  • Blind spot monitor sensor LH

CAUTION / NOTICE / HINT

NOTICE:

  • When checking for DTCs, make sure that the blind spot monitor system is on.
  • Before replacing the main body ECU (multiplex network body ECU), refer to Registration.

    w/ Smart Key System: Click here

PROCEDURE

1.

CONFIRM PART NUMBER (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

(a) Check the main body ECU (multiplex network body ECU) part number.

(1) Check if the part number of the main body ECU (multiplex network body ECU) installed on the vehicle is correct.

OK:

The part number is correct.

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

OK

2.

CHECK DTC

(a) Clear the DTCs.

Body Electrical > Blind Spot Monitor Master > Clear DTCs Body Electrical > Blind Spot Monitor Slave > Clear DTCs

(b) Recheck for DTCs and check if the same DTC is output again.

Body Electrical > Blind Spot Monitor Master > Trouble Codes Body Electrical > Blind Spot Monitor Slave > Trouble Codes

Result

Proceed to

No DTCs are output

A

DTC U1331 is output ("Blind Spot Monitor Master")

B

DTC U1331 is output ("Blind Spot Monitor Slave")

C
A

USE SIMULATION METHOD TO CHECK

B

REPLACE BLIND SPOT MONITOR SENSOR RH

C

REPLACE BLIND SPOT MONITOR SENSOR LH

    READ NEXT:

     Buzzer does not Sound

    WIRING DIAGRAM CAUTION / NOTICE / HINT NOTICE: When checking for DTCs, make sure that the blind spot monitor system is turned on. Inspect the fuses for circuits related to this system be

     Power Source Circuit

    DESCRIPTION This circuit provides power to operate the blind spot monitor sensor. WIRING DIAGRAM CAUTION / NOTICE / HINT NOTICE: Inspect the fuses for circuits related to this system before perfo

     Clearance Warning Buzzer

    ComponentsCOMPONENTS ILLUSTRATION *A for 7 Inch Display *B for 9 Inch Display *1 CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY *2 CENTER INSTRUMENT CLUSTER FINI

    SEE MORE:

     Installing the spare tire

    1. Remove any dirt or foreign matter from the wheel contact surface. If foreign matter is on the wheel contact surface, the wheel nuts may loosen while the vehicle is in motion, causing the tire to come off. 2. Install the tire and loosely tighten each wheel nut by hand by approximately

     Random/Multiple Cylinder Misfire Detected (P030000,P030027,P030085-P030600)

    DESCRIPTION When the engine misfires, high concentrations of hydrocarbons (HC) enter the exhaust gas. Extremely high hydrocarbon concentration levels can cause an increase in exhaust emission levels. Extremely high concentrations of hydrocarbons can also cause increases in the three-way catalytic co

    © 2023-2026 Copyright www.tocamry.com