Toyota Camry: Suggestion function
Displays suggestions to the driver in the following situations. To select
a response to a displayed suggestion, use the meter control switches.
The suggestion function can be turned on/off.
■ Suggestion to turn off the headlights
If the headlights are left on for a certain amount of time after the
engine switch has been turned off, if the headlight switch is in the
"AUTO" position, a suggestion message will be displayed asking if
you wish to turn the headlights off. To turn the headlights off, select
If a front door is opened after the engine switch is turned off, this suggestion
message will not be displayed.
■Eco Driving Indicator
- Eco Driving Indicator Light
During Eco-friendly acceleration (Eco
driving), the Eco Driving Indicator Light
will turn on. When the acceleration
exceeds the Zone of Eco driving, or
when the vehicle is stopped, the light
- Eco Driving Indicator Zone Display
Suggests the Zone of Eco driving with
current Eco driving ratio based on
- Eco driving ratio based on acceleration
If the acceleration exceeds the Zone of
Eco driving, the right side of the Eco
Driving Indicator Zone Display will illuminate.
- Zone of Eco driving
Eco Driving Indicator will not operate under the following conditions:
- The shift lever is in any position other than D.
- A paddle shift switch (if equipped) is operated.
- Neither normal mode nor Eco drive mode is selected.
- The vehicle speed is approximately 80 mph (130 km/h) or higher.
■Suspension of the settings display
- Some settings cannot be changed while driving. When changing settings,
park the vehicle in a safe place.
- If a warning message is displayed, operation of the settings display
- It may take a few minutes to display the tire inflation pressure after
engine switch is turned to IGNITION ON mode. It may also take a few minutes
to display the tire inflation pressure after inflation pressure has been
- "---" may be displayed if the tire position information cannot be
due to unfavorable radio wave conditions.
- Tire inflation pressure changes with temperature. The displayed values
also be different from the values measured using a tire pressure gauge.
■Liquid crystal display
Small spots or light spots may appear on the display. This phenomenon is
characteristic of liquid crystal displays, and there is no problem continuing to
use the display.
Some functions can be customized.
■Caution for use while driving
- When operating the multi-information display while driving, pay extra
attention to the safety of the area around the vehicle.
- Do not look continuously at the multi-information display while
you may fail to see pedestrians, objects on the road, etc. ahead of the
■The information display at low temperatures
Allow the interior of the vehicle to warm up before using the liquid
information display. At extremely low temperatures, the information display
monitor may respond slowly, and display changes may be delayed.
For example, there is a lag between the driver's shifting and the new gear
number appearing on the display. This lag could cause the driver to downshift
again, causing rapid and excessive engine braking and possibly an
accident resulting in death or injury.
■Cautions during setting up the display
As the engine needs to be running during setting up the display, ensure
the vehicle is parked in a place with adequate ventilation. In a closed area
such as a garage, exhaust gases including harmful carbon monoxide (CO)
may collect and enter the vehicle. This may lead to death or a serious
■While setting up the display
To prevent battery discharge, ensure that the engine is running while
up the display features.
The head-up display is linked to the meters and navigation system (if
equipped) and projects a variety of information in front of the driver,
such as the current vehicle speed.
Displays the following items in the appropriate situation:
Alert from the LTA (Lane Tracing Assist)
Dynamic radar cruise control with full-speed range
Brake Override Syste
PARTS LOCATION ILLUSTRATION
*1 FRONT NO. 2 SPEAKER ASSEMBLY (RH)
*2 DCM (TELEMATICS TRANSCEIVER) - BUB (BACK-UP BATTERY)
*3 AIRBAG SENSOR ASSEMBLY
*4 INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
- DCM FUSE - ECU-IG2 NO. 3 FUSE
- - IL
INSTALLATION CAUTION / NOTICE / HINT
Immediately after installing the front disc brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.
After replacing the front disc brake pads, the brake pedal ma