Toyota Camry owners & service manuals

Toyota Camry (XV70): USB Device Malfunction (B1585)

Toyota Camry Repair Manual XV70 (2018-2024) / Audio, Visual, Telematics / Audio / Video / Audio And Visual System / USB Device Malfunction (B1585)

DESCRIPTION

This DTC is stored when a malfunction occurs in a connected device.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

B1585

USB Device Malfunction

When any of the following conditions is met:

  • A non mass-storage class or incompatible protocol USB device connected
  • USB device with an incompatible file system, corrupted or incompatible File Allocation Table (FAT) connected
  • "iPod" malfunction
  • "iPod" with unsupported firmware connected
  • Unsupported "iPod" model connected
  • USB device or "iPod"
  • Radio and display receiver assembly

CAUTION / NOTICE / HINT

NOTICE:

  • Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

    Click here

  • When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:
    • A communication malfunction DTC may be stored.
    • The radio and display receiver assembly may not operate normally.

PROCEDURE

1.

REPLACE USB DEVICE OR "iPod"

(a) Disconnect the USB device or "iPod" from the No. 1 stereo jack adapter assembly.

(b) Turn the ignition switch off.

HINT:

When this DTC has been stored, it is necessary to turn the ignition switch off to make it possible for the vehicle to recognize a new device when it is connected.

(c) Turn the ignition switch to ACC.

(d) Connect a known good USB device or "iPod" to the No. 1 stereo jack adapter assembly.

HINT:

  • If the malfunction occurred when a USB device was in use, use another USB device for the inspection. If the malfunction occurred when an "iPod" was in use, use another "iPod" for the inspection.
  • Refer to System Description for compatible formats and versions.

    Click here

NEXT

2.

CHECK DTC

(a) Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs

(b) Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes

OK:

No DTCs are output.

OK

END (USB DEVICE FORMAT WAS INCOMPATIBLE, "iPod" VERSION WAS INCOMPATIBLE, OR USB DEVICE OR "iPod" WAS DEFECTIVE)
NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

    READ NEXT:

     AV Signal Stoppage (Low Battery Voltage) (B158F)

    DESCRIPTION This DTC is stored when a video or audio signal is interrupted due to battery voltage input to the radio and display receiver assembly dropping temporarily. DTC No. Detection Item

     Stereo Component Amplifier Malfunction (B15A3)

    DESCRIPTION This DTC is stored when a malfunction occurs in the stereo component amplifier assembly. DTC No. Detection Item DTC Detection Condition Trouble Area B15A3 Stereo C

     GPS Antenna Connection Malfunction(short) (B15C0,B15C1)

    DESCRIPTION These DTCs are stored when a malfunction occurs in the navigation antenna assembly. DTC No. Detection Item DTC Detection Condition Trouble Area B15C0 GPS Antenna C

    SEE MORE:

     Manual Shifting Test

    MANUAL SHIFTING TEST MANUAL SHIFTING TEST HINT: Using this test, it can be determined whether a problem is in an electrical circuit or if it is a mechanical problem in the transaxle. If any abnormalities are found in the following test, the problem is in the transaxle itself. (a) Dis

     Removal

    REMOVAL CAUTION / NOTICE / HINT The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during ECM removal/installation are shown below. Necessary Procedures After Parts Removed/Installed/Replaced

    © 2023-2025 Copyright www.tocamry.com