Toyota Camry (XV70): Customize Parameters
CUSTOMIZE PARAMETERS
CUSTOMIZE SLIDING ROOF SYSTEM
HINT:
The following items can be customized.
NOTICE:
- When the customer requests a change in a function, first make sure that the function can be customized.
- Be sure to make a note of the current settings before customizing.
- When troubleshooting a function, first make sure that the function is set to the default setting.
(a) Customizing with the Techstream
(1) Connect the Techstream to the DLC3.
(2) Turn the ignition switch to ON.
(3) Turn the Techstream on.
(4) Enter the following menus: Customize Setting / Power Window.
(5) Select the setting by referring to the table below.
Power Window|
Tester Display | Description |
Default | Setting |
ECU |
|---|---|---|---|---|
| Door Key P/W Up |
Function to close the power windows and sliding roof using the mechanical key |
OFF | 0:OFF,1:ON |
Main body ECU (Multiplex network body ECU) |
|
Door Key P/W Down | Function to open the power windows and sliding roof using the mechanical key |
OFF | 0:OFF,1:ON |
Main body ECU (Multiplex network body ECU) |
|
P/W Down W/ Transmit |
Function to open the power windows and sliding roof using the electrical key transmitter sub-assembly |
OFF | 0:OFF,1:ON |
Main body ECU (Multiplex network body ECU) |
(6) Enter the following menus: Customize Setting / Slide Roof.
(7) Select the setting by referring to the table below.
Slide Roof|
Tester Display | Description |
Default | Setting |
ECU |
|---|---|---|---|---|
| Door Key Related Operation |
Function to select tilt up or slide open of sliding roof key-linked function |
Slide | 0:Slide,1:Tilt |
Sliding roof ECU (Sliding roof drive gear sub-assembly) |
|
Wireless Key Related Operation |
Function to select tilt up or slide open of sliding roof wireless transmitter-linked function |
Slide | 0:Slide,1:Tilt |
Sliding roof ECU (Sliding roof drive gear sub-assembly) |
|
Front SW Auto Operation |
Function to enable/disable auto operation |
ON | 0:OFF,1:ON |
Sliding roof ECU (Sliding roof drive gear sub-assembly) |
(8) Enter the following menus: Customize Setting / Security.
(9) Select the setting by referring to the table below.
Security|
Tester Display | Description |
Default | Setting |
ECU |
|---|---|---|---|---|
| Slide Roof Open Warning |
Function to enable or disable the sliding roof open warning |
ON | 0:OFF,1:ON |
Main body ECU (Multiplex network body ECU) |
READ NEXT:
Initialization
INITIALIZATION INITIALIZE SLIDING ROOF SYSTEM
NOTICE:
When the sliding roof glass sub-assembly or sliding roof drive cable sub-assembly is adjusted or removed/installed, or the sliding roof d
Problem Symptoms Table
PROBLEM SYMPTOMS TABLE
HINT:
Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in or
Terminals Of Ecu
TERMINALS OF ECU CHECK SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)
(a) Disconnect the V2 sliding roof ECU (sliding roof drive gear sub-assembly) connector.
(b) Measure the resistanc
SEE MORE:
Child restraint systems
Before installing a child restraint system in the vehicle, there are
precautions that need to be observed, different types of child
restraint systems, as well as installation methods, etc., written in
this manual.
Use a child restraint system when riding with a small child that cannot
properly
Knock Sensor 1 Bank 1 or Single Sensor Circuit Short to Ground (P032511,P033011)
DESCRIPTION A flat-type knock control sensor (non-resonant type) has a structure that can detect vibrations between approximately 5 kHz and 15 kHz.
The knock control sensor is fitted onto the engine block to detect engine knocking.
The knock control sensor contains a piezoelectric element which
