Toyota Camry (XV70): Engine
ENGINE
HINT:
Perform these procedures after the engine has cooled down.
INSPECT DRIVE BELT
(a) Check the drive belt.
A25A-FKS: Click here
.gif)
2GR-FKS: Click here
INSPECT ENGINE OIL
(a) Check the engine oil.
A25A-FKS: Click here
2GR-FKS: Click here
REPLACE ENGINE OIL AND OIL FILTER
(a) Replace the engine oil and oil filter.
A25A-FKS: Click here
2GR-FKS: Click here
INSPECT COOLING AND HEATER SYSTEM
(a) Check that the radiator and condenser are not blocked with leaves, dirt or insects, and clean them if necessary. Also check the installation condition of the hoses and lines and the connecting parts for corrosion, etc.
A25A-FKS: Click here
2GR-FKS: Click here
INSPECT ENGINE COOLANT
(a) Check the engine coolant.
A25A-FKS: Click here
2GR-FKS: Click here
REPLACE ENGINE COOLANT
(a) Replace the engine coolant.
A25A-FKS: Click here
2GR-FKS: Click here
INSPECT SPARK PLUGS
(a) Check the spark plugs.
A25A-FKS: Click here
2GR-FKS: Click here
INSPECT BATTERY
(a) Check the battery.
A25A-FKS: Click here
2GR-FKS: Click here
INSPECT AIR CLEANER FILTER ELEMENT
(a) Remove the air cleaner filter element.
(b) Check that the air cleaner filter element is not excessively dirty.
If the air cleaner filter element is excessively dirty, replace the air cleaner filter element.
(c) If cleaning the air cleaner filter element, blow compressed air as shown in the illustration to clean it.
(d) Reinstall the air cleaner filter element.
INSPECT EXHAUST PIPES AND MOUNTINGS
(a) Visually check the pipes, hangers and connections for severe corrosion, leaks or damage.
INSPECT FUEL TANK CAP GASKET
(a) Check the fuel tank cap gasket.
A25A-FKS: Click here
2GR-FKS: Click here
INSPECT FUEL LINES, CONNECTIONS, FUEL TANK VAPOR VENT SYSTEM HOSES AND FUEL TANK BANDS
(a) Visually check the fuel lines and hoses for cracks, leaks, loose connections, or deformation.
(b) Check for tank band looseness or deformation.
INSPECT CHARCOAL CANISTER
(a) Check the charcoal canister.
A25A-FKS: Click here
2GR-FKS: Click here
READ NEXT:
Brake
BRAKE INSPECT BRAKE LINE PIPES AND HOSES HINT:
Work in a well-lighted area. Turn the front wheels fully to the right or left before beginning the inspection.
(a) Using a mirror, check the entire c
Chassis
CHASSIS INSPECT STEERING LINKAGE AND GEAR HOUSING
(a) Check the steering wheel free play. Click here
(b) Check the steering linkage for looseness or damage.
(1) Check that the tie rod ends do
Body
BODY TIGHTEN BOLTS AND NUTS ON CHASSIS AND BODY
(a) If necessary, tighten the bolts and nuts on the chassis parts listed below.
Front axle and suspension
Drivetrain
Rear axle and suspen
SEE MORE:
Torque Sensor Zero Point Adjustment Undone (C1515)
DESCRIPTION This DTC does not indicate a malfunction. The power steering ECU (rack and pinion power steering gear assembly) stores this DTC when it determines that torque sensor zero point calibration has not been performed.
When the IG terminal voltage is below 8 V, torque sensor zero point cali
Data List / Active Test
DATA LIST / ACTIVE TEST DATA LIST NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
HINT: Using the Techstream to read the Data List allows the values or state
