Toyota Camry (XV70): Green Indicator Remains Off
DESCRIPTION
After engine switch on (IG), the DCM (telematics transceiver) will enter into self check mode. The manual (SOS) switch red indicator will illuminate for 2 seconds and turn off followed by the manual (SOS) switch green indicator illuminating and remaining on under normal operation. If neither the red nor green indicators remain on, verification of the subscription should be performed.
PROCEDURE
| 1. |
CONFIRM GREEN INDICATOR COMES ON |
(a) After the engine switch is turned on (IG) and the manual (SOS) switch red indicator has come on for 2 seconds, confirm that the manual (SOS) switch green indicator comes on for 2 seconds.
OK:
Green indicator comes on.
| NG | .gif) | GO TO STEP 6 |
|
.gif)
| 2. |
CONFIRM SUBSCRIPTION MODE |
(a) Confirm the indicator status 5 seconds after the engine switch is turned on (IG).
|
Result | Proceed to |
|---|---|
|
Green indicator remains on |
A |
| Green indicator remains off |
B |
| A |
| USE SIMULATION METHOD TO CHECK
|
|
| 3. |
INPUT VIN WITH TECHSTREAM |
(a) Turn the engine switch off.
(b) Connect the Techstream to the DLC3.
(c) Turn the engine switch on (IG) and wait for 10 seconds.
(d) Turn the Techstream on.
(e) Choose "Telematics" from the System Selection Menu, and then click "Utility".
(f) Click "VIN Synchronization" on the Utility Selection Menu.
Click here
.gif)
|
| 4. |
CONFIRM SUBSCRIPTION MODE |
(a) Confirm the indicator status at 5 seconds after the engine switch is turned on (IG).
|
Result | Proceed to |
|---|---|
|
Green indicator remains on |
A |
| Green indicator remains off |
B |
| A |
| END |
|
| 5. |
REPLACE DCM (TELEMATICS TRANSCEIVER) |
(a) Replace the DCM (telematics transceiver).
Click here
NOTICE:
- The engine switch must be off.
- Do not exchange the DCM (telematics transceiver) with one from another vehicle.
| NEXT | | PERFORM DCM ACTIVATION |
| 6. |
CHECK DTC |
(a) Turn the engine switch off.
(b) Connect the Techstream to the DLC3.
(c) Turn the engine switch on (IG) and wait for 10 seconds or more.
(d) Turn the Techstream on.
(e) Clear the DTCs.
Body Electrical > Telematics > Clear DTCs(f) Check for DTCs and check that no DTCs are output.
Body Electrical > Telematics > Trouble CodesOK:
No DTCs are output.
| NG | |
GO TO DIAGNOSTIC TROUBLE CODE CHART
|
|
| 7. |
REPLACE DCM (TELEMATICS TRANSCEIVER) |
(a) Replace the DCM (telematics transceiver).
Click here
NOTICE:
- The engine switch must be off.
- Do not exchange the DCM (telematics transceiver) with one from another vehicle.
| NEXT | | PERFORM DCM ACTIVATION |
READ NEXT:
Red Indicator Remains On
DESCRIPTION This means that the DCM (telematics transceiver) has detected a malfunction in the safety connect system and stored a DTC or specific vehicle control history (RoB) Code. PROCEDURE
1.
Unable To Connect To Call Center
DESCRIPTION This may occur when the intensity of telephone radio frequency was very weak, or the safety connect system has a malfunction and a DTC is set. PROCEDURE
1.
CHECK COMMUNICATION S
Emergency Call Switch Illumination Circuit
WIRING DIAGRAM w/ Sliding Roof
w/o Sliding Roof
CAUTION / NOTICE / HINT
NOTICE:
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization
SEE MORE:
Suggestion function
Displays suggestions to the driver in the following situations. To select
a response to a displayed suggestion, use the meter control switches.
The suggestion function can be turned on/off.
■ Suggestion to turn off the headlights
If the headlights are left on for a certain amount of time aft
Internal Control Module Monitoring Processor Performance Watchdog/Safety MCU Failure (P060A47)
MONITOR DESCRIPTION The main CPU and sub CPU of the ECM perform data communication between each other. The main CPU monitors the communications and WDC pulses from the sub CPU. When the signal malfunctions below are detected, this DTC is stored.
DTC No. Detection Item
DTC Detection Cond
