Toyota Camry (XV70): Inspection
INSPECTION
PROCEDURE
1. INSPECT TURN SIGNAL SWITCH
| (a) Measure the resistance according to the value(s) in the table below.
Standard Resistance: Light Control Switch |
Tester Connection |
Condition | Specified Condition |
|
*1: w/ Light Control Switch DRL OFF Position
| | 2 (L_OFF) - 12 (EL) |
Light control switch in DRL OFF*1 |
Below 1 Ω | |
10 (A) - 12 (EL) |
Light control switch in AUTO position |
Below 1 Ω | |
14 (T) - 12 (EL) |
Light control switch in tail position |
Below 1 Ω | |
5 (H) - 12 (EL) |
Light control switch in head position |
Below 1 Ω | Dimmer Switch |
Tester Connection |
Condition | Specified Condition | |
6 (HF) - 12 (EL) |
Dimmer switch in high flash position |
Below 1 Ω | |
1 (HU) - 12 (EL) |
Dimmer switch in high position |
Below 1 Ω | Turn Signal Switch |
Tester Connection |
Condition | Specified Condition | |
9 (TR) - 12 (EL) |
Turn signal switch in neutral position |
10 kΩ or higher | |
3 (TL) - 12 (EL) |
Turn signal switch in neutral position |
10 kΩ or higher | |
9 (TR) - 12 (EL) |
Turn signal switch in right turn position |
Below 1 Ω | |
9 (TR) - 12 (EL) |
Turn signal switch in full right turn position |
Below 1 Ω | |
9 (TR) - 11 (CR) |
Turn signal switch in full right turn position |
Below 1 Ω | |
11 (CR) - 12 (EL) |
Turn signal switch in full right turn position |
Below 1 Ω | |
3 (TL) - 12 (EL) |
Turn signal switch in left turn position |
Below 1 Ω | |
3 (TL) - 12 (EL) |
Turn signal switch in full left turn position |
Below 1 Ω | |
3 (TL) - 11 (CR) |
Turn signal switch in full left turn position |
Below 1 Ω | |
11 (CR) - 12 (EL) |
Turn signal switch in full left turn position |
Below 1 Ω |
HINT:
- The left turn or right turn condition indicates a condition in which the turn signal switch will return to the neutral position after releasing your hand from the turn signal switch (turn signal switch is operated approximately 6.3
|
READ NEXT:
INSTALLATION PROCEDURE 1. INSTALL TURN SIGNAL SWITCH
(a) Engage the claw as shown in the illustration.
Install in this Direction (b) Install the turn signal switch with the
ComponentsCOMPONENTS ILLUSTRATION
*1 CENTER STOP LIGHT SET
- - RemovalREMOVAL PROCEDURE
1. REMOVE CENTER STOP LIGHT SET (a) Using a moulding remover, disengage the 2 claw
ComponentsCOMPONENTS ILLUSTRATION
*1 LICENSE PLATE LIGHT ASSEMBLY
*2 LUGGAGE COMPARTMENT DOOR COVER
*3 NO. 3 LUGGAGE COMPARTMENT DOOR OUTSIDE GARNISH
- -
SEE MORE:
DESCRIPTION These DTCs are stored when a malfunction occurs in the CAN communication circuit.
DTC No. Detection Item
DTC Detection Condition Trouble Area
U0073 Sending Malfunction (Navigation to APGS)
CAN bus connection error
CAN communication system
U010
PRECAUTION PRECAUTION FOR DISCONNECTING CABLE FROM NEGATIVE BATTERY TERMINAL
NOTICE: When disconnecting the cable from the negative (-) battery terminal, initialize the following system(s) after the cable is reconnected:
System Name See Procedure
Lane Tracing Assist System