Toyota Camry (XV70): Installation
INSTALLATION
PROCEDURE
1. PRECAUTION
NOTICE:
- When replacing the radio and display receiver assembly or navigation ECU, always replace it with a new one. If a radio and display receiver assembly or navigation ECU which was installed to another vehicle is used, the following may occur:
- A communication malfunction DTC may be stored.
- The radio and display receiver assembly or navigation ECU may not operate normally.
- After replacing the navigation ECU, if "New software is not compatible with the system. Contact your dealer." is displayed on the multi-display, update the software of the radio and display receiver assembly.
2. INSTALL NAVIGATION ECU
3. INSTALL DCM (TELEMATICS TRANSCEIVER) (w/ Manual (SOS) Switch)
4. INSTALL NO. 1 TELEPHONE BRACKET
(a) w/o Manual (SOS) Switch:
(1) Install the No. 1 telephone bracket with the 2 screws.
(b) w/ Manual (SOS) Switch:
(1) Install the No. 1 telephone bracket with the 3 screws.
5. INSTALL NO. 2 TELEPHONE BRACKET
(a) w/o Manual (SOS) Switch:
(1) Install the No. 2 telephone bracket with the 2 screws.
(b) w/ Manual (SOS) Switch:
(1) Install the No. 2 telephone bracket with the 3 screws.
6. INSTALL ANTENNA CORD SUB-ASSEMBLY
(a) w/o Manual (SOS) Switch:
(1) Engage the clamp to install the antenna cord sub-assembly.
(2) Connect the connector.
(b) w/ Manual (SOS) Switch:
(1) Engage the clamp to install the antenna cord sub-assembly.
(2) Connect the 4 connectors.
7. INSTALL NAVIGATION ECU WITH BRACKET
(a) Connect each connector.
(b) Engage the clamp.
(c) Engage the 3 guides.
(d) Install the navigation ECU with bracket with the 3 bolts.
(e) Connect each connector.
8. INSTALL REAR UPPER CONSOLE PANEL SUB-ASSEMBLY
Click here
.gif)
9. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY
for UB80E:
Click here
for UA80E:
Click here
for UB80F:
Click here
10. INSTALL SHIFT LOCK RELEASE BUTTON COVER
for UB80E:
Click here
for UA80E:
Click here
for UB80F:
Click here
11. INSTALL LOWER CENTER INSTRUMENT PANEL FINISH PANEL
Click here
12. INSTALL INSTRUMENT PANEL FINISH PLATE GARNISH
Click here
13. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY
Click here
14. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (for 7 Inch Display)
Click here
15. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (for 9 Inch Display)
Click here
16. INSTALL AIR CONDITIONING CONTROL ASSEMBLY
Click here
READ NEXT:
Precaution
PRECAUTION PRECAUTION FOR DISCONNECTING CABLE FROM NEGATIVE BATTERY TERMINAL
NOTICE:
After the engine switch is turned off, the radio and display receiver assembly records various types of memor
Parts Location
PARTS LOCATION ILLUSTRATION
*1 ROOF CONSOLE BOX SUB-ASSEMBLY
*2 TELEPHONE MICROPHONE ASSEMBLY
*3 ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY
- TV FUSE *4
SEE MORE:
Radio Broadcast cannot be Received or Poor Reception
CAUTION / NOTICE / HINT
NOTICE:
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.
Click here
When replacing the radio and display receiver
If a warning message
is displayed
The multi-information display shows warnings of system malfunctions,
incorrectly performed operations, and messages that
indicate a need for maintenance. When a message is shown,
perform the correction procedure appropriate to the message.
4.2-inch display
7-inch display
Master warning
