Toyota Camry (XV70): Installation
INSTALLATION
PROCEDURE
1. INSTALL FUEL PUMP CONTROL ECU BRACKET
(a) Install the fuel pump control ECU bracket to the fuel pump control ECU with the 2 bolts.
Torque:
4.5 N·m {46 kgf·cm, 40 in·lbf}
2. INSTALL FUEL PUMP CONTROL ECU
(a) Install the fuel pump control ECU to the vehicle body with the nut.
Torque:
8.0 N·m {82 kgf·cm, 71 in·lbf}
(b) Connect the 2 fuel pump control ECU connectors.
3. INSTALL ROOM PARTITION BOARD LH
Click here
.gif)
4. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY
Click here
5. INSTALL REAR SEAT SHOULDER BELT HOLE COVER
Click here
6. INSTALL INNER ROOF SIDE GARNISH LH
Click here
7. INSTALL INNER ROOF SIDE GARNISH RH
HINT:
Use the same procedure as for the LH side.
8. CONNECT REAR SEAT OUTER BELT ASSEMBLY LH
Click here
9. CONNECT REAR SEAT OUTER BELT ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
10. INSTALL CENTER STOP LIGHT SET
Click here
11. INSTALL REAR SIDE SEATBACK ASSEMBLY LH (for Fold Down Seat Type)
Click here
12. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH (for Fold Down Seat Type)
Click here
13. INSTALL REAR SIDE SEATBACK ASSEMBLY RH (for Fold Down Seat Type)
HINT:
Use the same procedure as for the LH side.
14. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH (for Fold Down Seat Type)
HINT:
Use the same procedure as for the LH side.
15. INSTALL REAR SEATBACK ASSEMBLY LH (for Fold Down Seat Type)
Click here
16. INSTALL REAR SEAT CUSHION LOCK HOOK (for Fold Down Seat Type)
Click here
17. INSTALL REAR SEAT CUSHION ASSEMBLY (for Fold Down Seat Type)
Click here
18. INSTALL REAR SEAT HEADREST ASSEMBLY LH (w/ Removable Headrest)
Click here
19. INSTALL REAR SEAT ASSEMBLY (for Fixed Seat Type)
Click here
20. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click here
21. PERFORM DIAGNOSTIC SYSTEM CHECK
Click here
22. INSPECT SRS WARNING LIGHT
Click here
READ NEXT:
Components
COMPONENTS ILLUSTRATION
*A for Fold Down Seat Type
- -
*1 REAR CENTER SEAT OUTER BELT ASSEMBLY
*2 REAR SEAT CUSHION ASSEMBLY
*3 REAR SEAT CUSHION LOCK H
Removal
REMOVAL CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fu
Installation
INSTALLATION PROCEDURE 1. INSTALL FUEL PUMP CONTROL ECU BRACKET
(a) Install the fuel pump control ECU bracket to the fuel pump control ECU with the 2 bolts.
Torque: 4.5 N·m {46 kgf·cm, 40 in·l
SEE MORE:
Vehicle Speed Sensor "A" No Signal (P050031)
DESCRIPTION Vehicles, which are equipped with ABS (Anti-lock Brake System), detect the vehicle speed using the skid control ECU (brake actuator assembly) and speed sensor. The speed sensor monitors the wheel rotation speed and sends a signal to the skid control ECU. The skid control ECU converts the
Disassembly
DISASSEMBLY CAUTION / NOTICE / HINT
NOTICE:
As imbalance affects vibration and noise performance, make sure to ensure correct angular alignment of the following components during installation.
PROPELLER INTERMEDIATE SHAFT ASSEMBLY
REAR PROPELLER SHAFT ASSEMBLY
LARGE DIAMETER PR
