Toyota Camry (XV70): Open in Outer Mirror Indicator(Slave) (C1AB5)
DESCRIPTION
This DTC is stored when the blind spot monitor sensor LH detects an open in the outer rear view mirror indicator LH.
|
DTC No. | Detection Item |
DTC Detection Condition | Trouble Area |
|---|---|---|---|
|
C1AB5 | Open in Outer Mirror Indicator(Slave) | Both of the following conditions are met:
|
|
WIRING DIAGRAM
.png)
CAUTION / NOTICE / HINT
NOTICE:
When checking for DTCs, make sure that the blind spot monitor system is turned on.
PROCEDURE
| 1. |
CHECK DTC |
(a) Turn the engine switch off.
(b) Turn the engine switch on (IG).
(c) Recheck for DTCs and check if the same DTC is output again.
Body Electrical > Blind Spot Monitor Slave > Trouble CodesOK:
No DTCs are output.
| OK | .gif) |
USE SIMULATION METHOD TO CHECK |
|
.gif)
| 2. |
CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER LH - BLIND SPOT MONITOR SENSOR LH AND BODY GROUND) |
(a) Disconnect the W6 blind spot monitor sensor LH connector.
(b) Disconnect the O20*1 or O21*2 outer rear view mirror assembly with cover LH connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection | Condition |
Specified Condition |
|---|---|---|
|
W6-4 (OMIL) - O20-1 (BSL+)*1 |
Always | Below 1 Ω |
|
O20-4 (E) - Body ground*1 |
Always | Below 1 Ω |
|
W6-4 (OMIL) - O21-8 (BSL+)*2 |
Always | Below 1 Ω |
|
O21-15 (E) - Body ground*2 |
Always | Below 1 Ω |
- *1: w/o Panoramic View Monitor System
- *2: w/ Panoramic View Monitor System
| NG | | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
| 3. |
INSPECT OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER LH |
(a) Disconnect the IND2 outer mirror LH connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection | Condition |
Specified Condition |
|---|---|---|
|
O20-1 (BSL+) - IND2-2 (+)*1 |
Always | Below 1 Ω |
|
O20-4 (E) - IND2-1 (-)*1 |
Always | Below 1 Ω |
|
O21-8 (BSL+) - IND2-2 (+)*2 |
Always | Below 1 Ω |
|
O21-15 (E) - IND2-1 (-)*2 |
Always | Below 1 Ω |
- *1: w/o Panoramic View Monitor System
- *2: w/ Panoramic View Monitor System
| NG | | REPLACE OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER LH
|
|
| 4. |
INSPECT OUTER MIRROR LH |
(a) Remove the outer mirror LH.
Click here .gif)
(b) Inspect the outer rear view mirror indicator LH on the outer mirror LH.
Click here
| OK | | REPLACE BLIND SPOT MONITOR SENSOR LH
|
| NG | | REPLACE OUTER MIRROR LH |
READ NEXT:
Blind Spot Monitor Master Module (C1AB6)
DESCRIPTION This DTC is stored when the blind spot monitor sensor RH detects an internal malfunction.
DTC No. Detection Item
DTC Detection Condition Trouble Area
C1AB6 Blind S
Blind Spot Monitor Slave Module (C1AB7)
DESCRIPTION This DTC is stored when the blind spot monitor sensor LH detects an internal malfunction.
DTC No. Detection Item
DTC Detection Condition Trouble Area
C1AB7 Blind S
Destination Information Undefined (C1AB8)
DESCRIPTION This DTC is stored when correct destination information is not sent from the main body ECU (multiplex network body ECU) and destination information cannot be confirmed after a blind spot m
SEE MORE:
VEHICLE CONTROL HISTORY (RoB)
VEHICLE CONTROL HISTORY (RoB) DESCRIPTION
Vehicle Control History (RoB) is a function that captures and stores ECU data when triggered by specific vehicle behavior.
It may be possible to determine the cause of the malfunction by checking the vehicle history information and freeze frame dat
Removal
REMOVAL CAUTION / NOTICE / HINT
HINT: If the bumper is damaged, there is a possibility that the installation area of the blind spot monitor sensor may be deformed and the blind spot monitor system may not operate correctly, so visually inspect the blind spot monitor sensor installation area (fram
