Toyota Camry (XV70): Problem Symptoms Table
PROBLEM SYMPTOMS TABLE
NOTICE:
- When replacing the forward recognition camera, replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle and a DTC may be stored.
- When the forward recognition camera is replaced with a new one or the windshield glass is replaced or removed/installed, make sure to read Before Starting Adjustment, then perform optical axis alignment for the forward recognition camera and clear the vehicle control history for each system.
HINT:
Forward recognition camera axis alignment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment.
One Time Recognition: Click here
.gif)
Sequential Recognition: Click here
Driving Adjustment: Click here
- When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
HINT:
- If no problem symptoms are found when a DTC is output in the DTC check on the lane tracing assist system, check each symptom by checking the suspected areas in the order they are listed.
- Before performing failure diagnosis according to the following inspection points, check the forward recognition camera system power source circuit fuses and relays.
|
Symptom | Suspected Area |
Link |
|---|---|---|
|
The lane tracing assist system does not operate at all |
Steering pad switch circuit |
|
|
Forward recognition camera adjustment HINT: Forward recognition camera axis alignment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment. |
One Time Recognition: Sequential Recognition: Driving Adjustment: | |
|
The LTA indicator light does not turn on or off even by operating the LTA switch |
Indicator circuit |
|
|
Steering pad switch circuit |
| |
|
Forward recognition camera |
| |
|
The lane tracing assist system is not canceled even by operating the turn signals |
Data List/Active Test (Turn Switch) |
|
|
Turn signal switch circuit |
| |
|
The lane tracing assist system does not operate many times even when the white lines are visible |
Check conditions for operating/not operating |
|
|
Forward recognition camera adjustment HINT: Forward recognition camera axis alignment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment. |
One Time Recognition: Sequential Recognition: Driving Adjustment: | |
|
The lane tracing assist system is operating but the system control status is not displayed on the multi-information display |
Data List/Active Test (LDA Control) |
|
|
Combination meter assembly |
| |
|
The lane departure warning function is on but the buzzer does not sound even when straying from white line |
Combination meter assembly |
|
READ NEXT:
Terminals Of Ecu
TERMINALS OF ECU
NOTICE:
DTCs may be output when connectors are disconnected during inspection. Therefore, be sure to clear the DTCs using the Techstream once the inspection has been completed.
Diagnosis System
DIAGNOSIS SYSTEM DIAGNOSIS MODE FUNCTION (a) When a malfunction occurs in the lane tracing assist system, the LTA indicator light illuminates in yellow and a message is displayed on the multi-informat
Dtc Check / Clear
DTC CHECK / CLEAR CHECK FOR DTC (a) Check for DTCs (Test Failed / Pending / Confirmed). Chassis > Lane Control > Trouble Codes
Techstream Display Description
Test Failed Shows
SEE MORE:
Removal
REMOVAL CAUTION / NOTICE / HINT
NOTICE:
Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.
After replacing the rear disc brake pads, always perform a road test to check
Parts Location
PARTS LOCATION ILLUSTRATION
*1 CANISTER (CHARCOAL CANISTER ASSEMBLY)
*2 FUEL TANK CAP ASSEMBLY
*3 PCV VALVE (VENTILATION VALVE SUB-ASSEMBLY)
*4 PURGE VALVE (PURGE VSV)
*5 ECM
*6 ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY
- EFI-MAIN
