Toyota Camry owners & service manuals

Toyota Camry (XV70): Rear Brake Flexible Hose (w/ Electric Parking Brake System)

Toyota Camry Repair Manual XV70 (2018-2024) / General / Maintenance / Rear Brake Flexible Hose (w/ Electric Parking Brake System)

Components

COMPONENTS

ILLUSTRATION

*1

REAR FLEXIBLE HOSE

*2

GASKET

*3

UNION BOLT

*4

BRAKE LINE

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf)

*

For use with a union nut wrench

Non-reusable part

-

-

Removal

REMOVAL

CAUTION / NOTICE / HINT

NOTICE:

If both left and right rear flexible hoses are disconnected at the same time, be sure to place an identification mark on each hose to indicate its installation position.

HINT:

  • Use the same procedure for the RH side and LH side.
  • The following procedure is for the LH side.

PROCEDURE

1. REMOVE REAR WHEEL

Click here

2. DRAIN BRAKE FLUID

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.

3. REMOVE REAR FLEXIBLE HOSE

(a) Remove the union bolt and gasket, and disconnect the rear flexible hose from the rear disc brake cylinder assembly.

(b) Remove the bolt and separate the rear flexible hose from the rear flexible hose bracket.

(c) Using a union nut wrench, disconnect the brake line while holding the rear flexible hose with a wrench.

NOTICE:

  • Do not kink or damage the brake line.
  • Do not allow any foreign matter such as dirt or dust to enter the brake line from the connecting parts.

(d) Remove the clip and rear flexible hose from the vehicle body.

Installation

INSTALLATION

CAUTION / NOTICE / HINT

NOTICE:

  • Because the left and right rear flexible hoses are not interchangeable, verify the part number when installing the rear flexible hoses.
  • When reusing the rear flexible hoses, use the identification marks created during removal to install each rear flexible hose to its original position.

HINT:

  • Use the same procedure for the RH side and LH side.
  • The following procedure is for the LH side.

PROCEDURE

1. INSTALL REAR FLEXIBLE HOSE

NOTICE:

When installing the rear flexible hose, minimize twisting of the hose.

(a) Install the rear flexible hose with a new clip.

NOTICE:

  • Install the clip as far as it will go.
  • When installing the rear flexible hose, face the identification mark to the upper side of the vehicle.

*a

Identification Mark

*b

Torque Wrench Fulcrum Length

*c

Union Nut Wrench

(b) Using a union nut wrench, connect the brake line to the rear flexible hose while holding the rear flexible hose with a wrench.

Torque:

Specified tightening torque :

15.2 N

    READ NEXT:

     Rear Brake Flexible Hose (w/o Electric Parking Brake System)

    ComponentsCOMPONENTS ILLUSTRATION *1 REAR FLEXIBLE HOSE *2 GASKET *3 UNION BOLT - - Tightening torque for "Major areas involving basic vehicle perf

     Rear Disc Brake Pad (w/ Electric Parking Brake System)

     Components

    COMPONENTS ILLUSTRATION *1 NO. 2 PARKING BRAKE WIRE ASSEMBLY *2 REAR DISC BRAKE ANTI-SQUEAL SHIM KIT *3 REAR DISC BRAKE PAD *4 REAR DISC BRAKE CYLINDER ASSEMBLY

    SEE MORE:

     Inspection

    INSPECTION PROCEDURE 1. INSPECT COMBINATION SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY) (a) Inspect the NORMAL mode switch: (1) Measure the resistance according to the value(s) in the table below. Standard Resistance: Tester Connection Condition Specified Condition

     No Sound can be Heard from Speakers

    PROCEDURE 1. CHECK AUDIO SETTINGS (a) In sound output setting mode, set volume, fader and balance to the initial values and check that the sound is normal. OK: Audio system returns to normal. HINT: Sound quality adjustment measures vary according to the type of amplifier. OK

    © 2023-2025 Copyright www.tocamry.com