Toyota Camry (XV70): Right Electric Parking Brake Actuator Control Circuit Open (C061013)
DESCRIPTION
|
DTC No. | Detection Item |
DTC Detection Condition | Trouble Area |
Memory | Note |
|---|---|---|---|---|---|
|
C061013 | Right Electric Parking Brake Actuator Control Circuit Open |
|
| DTC stored |
An electric parking brake system malfunction is displayed on the multi-information display. |
WIRING DIAGRAM
Click here .gif)
PROCEDURE
| 1. |
INSPECT NO. 1 PARKING BRAKE WIRE ASSEMBLY |
(a) Turn the ignition switch off.
(b) Make sure that there is no looseness at the locking part and the connecting part of the connectors.
OK:
The connector is securely connected.
(c) Disconnect the uR2 and u1 No. 1 parking brake wire assembly connectors.
(d) Check both the connector case and the terminals for deformation and corrosion.
OK:
No deformation or corrosion.
(e) Measure the resistance according to the value(s) in the table below.
.png)
|
*a | Front view of No. 1 Parking Brake Wire Assembly |
*b | (to wire harness connector) |
|
*c | (to Parking Brake Actuator Assembly RH) |
- | - |
Standard Resistance:
|
Tester Connection | Condition |
Specified Condition |
|---|---|---|
|
uR2-2 - u1-2 (RE+) | Always |
Below 1 Ω |
|
uR2-2 - Other terminals |
Always | 10 kΩ or higher |
|
uR2-1 - u1-1 (RE-) | Always |
Below 1 Ω |
|
uR2-1 - Other terminals |
Always | 10 kΩ or higher |
| NG | .gif) | REPLACE NO. 1 PARKING BRAKE WIRE ASSEMBLY |
|
.gif)
| 2. |
CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - PARKING BRAKE ACTUATOR ASSEMBLY RH) |
(a) Turn the ignition switch off.
(b) Make sure the No. 1 parking brake wire assembly is securely installed.
(c) Disconnect the A34 skid control ECU (brake actuator assembly) connector.
(d) Disconnect the u1 parking brake actuator assembly RH connector.
(e) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection | Condition |
Specified Condition |
|---|---|---|
|
A34-2 (MRR+) - u1-2 (RE+) |
Always | Below 1 Ω |
|
A34-3 (MRR-) - u1-1 (RE-) |
Always | Below 1 Ω |
| NG | | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
| 3. |
INSPECT PARKING BRAKE ACTUATOR ASSEMBLY RH |
(a) Remove the parking brake actuator assembly RH.
Click here
(b) Inspect the parking brake actuator assembly RH.
Click here
| OK | | REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) |
| NG | | REPLACE PARKING BRAKE ACTUATOR ASSEMBLY RH |
READ NEXT:
Right Electric Parking Brake Actuator Signal Stuck In Range (C06132A)
DESCRIPTION
DTC No. Detection Item
DTC Detection Condition Trouble Area
Memory Note
C06132A Right Electric Parking Brake Actuator Signal Stuck In Range
Diagn
Electric Parking Brake Actuator (C13B800)
DESCRIPTION
DTC No. Detection Item
DTC Detection Condition Trouble Area
Memory Note
C13B800 Electric Parking Brake Actuator
Diagnosis Condition:
Electric
Electric Parking Brake does not Operate
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE: Inspect the fuses for circuits related to this system before performing the following procedure.
HINT: Even if the electric parking brake is opera
SEE MORE:
Right Rear Wheel ABS Hold Solenoid Control Circuit Short to Battery (C12E712,...,C12F249)
DESCRIPTION The ABS solenoid relay and solenoid valves are built into the brake actuator assembly.
The rear solenoid valve RH controls the brake fluid pressure of the rear wheel cylinder RH of the vehicle.
When this DTC is stored, the fail-safe function operates and the ABS solenoid relay is tur
Cellular Phone Inspection
PROCEDURE
1. CHECK USAGE CONDITION
(a) Check that the vehicle and cellular phone meet the following conditions:
NOTICE: If changing cellular phone settings, updating software, etc. is necessary, make sure to obtain the permission of the customer before performing it.
The cellula
