Toyota Camry (XV70): Utility
UTILITY
Recognition Camera/Target Position Memory
HINT:
Recognition Camera/Target Position Memory is used to enter required information into the forward recognition camera.
(a) Perform Recognition Camera/Target Position Memory according to the display on the Techstream.
Chassis > Front Recognition Camera > Utility|
Tester Display |
|---|
| Recognition Camera/Target Position Memory |
HINT:
For forward recognition camera adjustment procedures.
Forward recognition camera axis alignment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment.
One Time Recognition: Click here .gif)
Sequential Recognition: Click here
HINT:
Recognition Camera Axis Adjust is used to calibrate the internal data of the forward recognition camera to enhance its recognition accuracy.
Recognition Camera Axis Adjust
(a) Perform Recognition Camera Axis Adjust according to the display on the Techstream.
for Type A
Chassis > Front Recognition Camera > Utility|
Tester Display |
|---|
| Recognition Camera Axis Adjust |
for Type B
Chassis > Front Recognition Camera > Utility|
Tester Display |
|---|
| Recognition Camera Axis Adjust |
HINT:
For forward recognition camera adjustment procedures.
Forward recognition camera axis alignment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment.
One Time Recognition: Click here
Sequential Recognition: Click here
Initial Axis Adjust Value Display
HINT:
This utility is used to display the initial axis adjust value display stored in the forward recognition camera.
(a) Following the instructions on the Techstream, perform "Initial Axis Adjust Value Display".
Chassis > Front Recognition Camera > Utility|
Tester Display |
|---|
| Initial Axis Adjust Value Display |
Front Recognition Camera Axis Misalignment Reading
HINT:
This utility is used to check the front recognition camera axis misalignment reading calculated by the forward recognition camera.
(a) Following the instructions on the Techstream, perform "Front Recognition Camera Axis Misalignment Reading".
Chassis > Front Recognition Camera > Utility|
Tester Display |
|---|
| Front Recognition Camera Axis Misalignment Reading |
Transition to Online Axis Alignment Mode
NOTICE:
This utility transitions to online axis alignment mode of the forward recognition camera.
(a) Following the instructions on the Techstream, perform "Transition to Online Axis Alignment Mode".
for Type A
Chassis > Front Recognition Camera > Utility|
Tester Display |
|---|
| Transition to Online Axis Alignment Mode |
for Type B
Chassis > Front Recognition Camera > Utility|
Tester Display |
|---|
| Transition to Online Axis Alignment Mode |
PCS Image Information Clear
HINT:
PCS Image Information Clear is used to clear the PCS Image Information data.
(a) Perform PCS Image Information Clear according to the display on the Techstream.
Chassis > Front Recognition Camera > Utility|
Tester Display |
|---|
| PCS Image Information Clear |
PCS Image Record Setting
HINT:
PCS Image Record Setting is used to activate/deactivate the PCS image recording function.
(a) Perform PCS Image Record Setting according to the display on the Techstream.
Chassis > Front Recognition Camera > Utility|
Tester Display |
|---|
| PCS Image Record Setting |
READ NEXT:
Problem Symptoms Table
PROBLEM SYMPTOMS TABLE
HINT:
Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order
Terminals Of Ecu
TERMINALS OF ECU
NOTICE:
DTCs may be output when connectors are disconnected during inspection. Therefore, be sure to clear the DTCs using the Techstream once the inspection has been completed.
Diagnosis System
DIAGNOSIS SYSTEM DIAGNOSIS FUNCTION (a) If a malfunction is detected in the forward recognition camera, the forward recognition camera stores a DTC without directly informing the driver via indicator
SEE MORE:
Lost Communication with Blind Spot Monitor Master Module (U0233)
DESCRIPTION This DTC is stored when the blind spot monitor sensor LH judges that there is a communication problem with the blind spot monitor sensor RH.
DTC No. Detection Item
DTC Detection Condition Trouble Area
U0233 Lost Communication with Blind Spot Monitor Master Module
Reassembly
REASSEMBLY PROCEDURE 1. CLEAN VACUUM PUMP HOUSING
(a) Clean the inside surface of the vacuum pump housing. 2. INSTALL VACUUM PUMP ROTOR
(a) Clean the vacuum pump rotor. (b) Apply engine oil to the areas of the vacuum pump rotor shown in the illustration.
Engine Oil (c) Instal
