Toyota Camry owners & service manuals

Toyota Camry (XV70): Air Vent cannot be Switched

DESCRIPTION

If the air outlet mode does not change even though the air outlet display changes, the following suspected areas may be the cause.

Symptom

Factor

Air outlet mode cannot be changed (air outlet display changes)

  • No. 1 air conditioning radiator damper servo sub-assembly malfunction
  • No. 2 air conditioning radiator damper servo sub-assembly malfunction*
  • Damper link disconnection
  • Air conditioner unit assembly malfunction
  • *: w/ Rear Center Register

PROCEDURE

1.

CONFIRM MODEL

(a) Choose the model to be inspected.

Result

Proceed to

w/ Rear Center Register

A

w/o Rear Center Register

B

B

GO TO STEP 5

A

2.

CHECK AIR OUTLET SERVO MOTOR

(a) Confirm for which seat the air outlet mode cannot be changed.

Result

Proceed to

The air outlet mode for the front seats cannot be changed

A

The air outlet mode for the rear seats cannot be changed

B

A

GO TO STEP 5

B

3.

CHECK NO. 2 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY

(a) Check that the No. 2 air conditioning radiator damper servo sub-assembly is installed correctly.

OK:

The No. 2 air conditioning radiator damper servo sub-assembly is installed correctly.

NG

INSTALL NO. 2 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY

OK

4.

CHECK FOR DTC

(a) Connect the GTS to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the GTS on.

(d) Enter the following menus: Body Electrical / Air Conditioner / Trouble Codes.

(e) Check for DTCs.

Body Electrical > Air Conditioner > Trouble Codes

Result

Proceed to

B1449 is not output

A

B1449 is output

B

A

REPLACE AIR CONDITIONING RADIATOR ASSEMBLY

B

GO TO DTC B1449

5.

CHECK NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY

(a) Check that the No. 1 air conditioning radiator damper servo sub-assembly is installed correctly.

OK:

The No. 1 air conditioning radiator damper servo sub-assembly is installed correctly.

NG

INSTALL NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY

OK

6.

CHECK FOR DTC

(a) Connect the GTS to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the GTS on.

(d) Enter the following menus: Body Electrical / Air Conditioner / Trouble Codes.

(e) Check for DTCs.

Body Electrical > Air Conditioner > Trouble Codes

Result

Proceed to

B1443 is not output

A

B1443 is output

B

A

REPLACE AIR CONDITIONING RADIATOR ASSEMBLY

B

GO TO DTC B1443

    READ NEXT:

     Air Vent Temperature does not Change and Right Vent is Different from Left and Vice Versa (Same Left/Right Temperature Setting)

    DESCRIPTION If the temperature of the air that blows from the left and right front registers differs, even though the same temperature is set for both sides, the following suspected areas may be the c

     No Warm Air Comes Out

    DESCRIPTION If cool air blows from the registers regardless of the temperature setting of the air conditioning system, the following suspected areas may be the cause. Symptom Factor

     Air Conditioning System (for Manual Air Conditioning System)

    SEE MORE:

     Disassembly

    DISASSEMBLY CAUTION / NOTICE / HINT HINT: Use the same procedure for the RH side and LH side. The following procedure is for the LH side. PROCEDURE 1. REMOVE REAR SIDE MARKER LIGHT BULB (for Bulb Type Back-up Light) (a) Turn the rear combination light socket and wire with the r

     Components

    COMPONENTS ILLUSTRATION *1 FRONT LOWER NO. 1 FLOOR HEAT INSULATOR - - N*m (kgf*cm, ft.*lbf): Specified torque - - ILLUSTRATION *1 PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY *2 CENTER NO. 2 SUPPORT BEARING WASHER Tight

    © 2023-2026 Copyright www.tocamry.com