Toyota Camry (XV70): Components
COMPONENTS
ILLUSTRATION
|
*1 | FRONT DISC BRAKE ANTI-SQUEAL SHIM KIT |
*2 | FRONT DISC BRAKE PAD |
|
*3 | FRONT FLEXIBLE HOSE |
*4 | FRONT DISC BRAKE CYLINDER ASSEMBLY |
|
*5 | FRONT NO. 1 DISC BRAKE ANTI-SQUEAL SHIM |
*6 | FRONT NO. 2 DISC BRAKE ANTI-SQUEAL SHIM |
|
*7 | FRONT DISC BRAKE PAD WEAR INDICATOR PLATE |
*8 | GASKET |
|
*9 | UNION BOLT |
- | - |
 |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) |
● | Non-reusable part |
 |
Brake shim grease (Part No. 08887-80409) |
- | - |
ILLUSTRATION
|
*A | for Type A |
*B | for Type B |
|
*1 | FRONT DISC |
*2 | FRONT DISC BRAKE BUSHING DUST BOOT |
|
*3 | FRONT DISC BRAKE CYLINDER MOUNTING |
*4 | FRONT DISC BRAKE CYLINDER SLIDE PIN |
|
*5 | FRONT DISC BRAKE PAD SUPPORT PLATE |
*6 | FRONT DISC BRAKE CYLINDER SLIDE BUSHING |
|
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) |
● | Non-reusable part |
|
|
Lithium soap base glycol grease |
- | - |
ILLUSTRATION
|
*1 | CYLINDER BOOT |
*2 | FRONT DISC BRAKE BLEEDER PLUG |
|
*3 | FRONT DISC BRAKE BLEEDER PLUG CAP |
*4 | FRONT DISC BRAKE PISTON |
|
*5 | PISTON SEAL |
*6 | FRONT DISC BRAKE CYLINDER |
|
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) |
● | Non-reusable part |
|
|
Lithium soap base glycol grease |
- | - |
READ NEXT:
Removal
REMOVAL CAUTION / NOTICE / HINT
NOTICE:
Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to
Disassembly
DISASSEMBLY PROCEDURE 1. REMOVE FRONT DISC BRAKE PISTON
(a) Place a piece of cloth between the front disc brake piston and front disc brake cylinder.
*a Cloth
Inspection
INSPECTION PROCEDURE 1. INSPECT BRAKE CYLINDER AND PISTON
(a) Check the front disc brake cylinder bore and front disc brake piston for rust and scoring. If necessary, replace the front disc brake cy
SEE MORE:
Removal
REMOVAL CAUTION / NOTICE / HINT
HINT:
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
PROCEDURE 1. REMOVE REAR WHEEL Click here
2. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY Click here
3. REMOVE PARKING BRAKE SHOE ADJUSTING HOLE
Left Rear Wheel Speed Sensor Circuit Voltage Out of Range (C050C1C)
DESCRIPTION Refer to DTC C050C12 Click here
DTC No. Detection Item
DTC Detection Condition Trouble Area
C050C1C Left Rear Wheel Speed Sensor Circuit Voltage Out of Range
When the vehicle is being driven in a straight line at a speed of 20 km/h (12 mph) or more
