Toyota Camry owners & service manuals

Toyota Camry (XV70): How To Proceed With Troubleshooting

CAUTION / NOTICE / HINT

HINT:

  • Use the following procedure to troubleshoot the blind spot monitor system.
  • *: Use the Techstream.

PROCEDURE

1.

VEHICLE BROUGHT TO WORKSHOP

NEXT

2.

CUSTOMER PROBLEM ANALYSIS

HINT:

If there are any scratches or impact marks on the rear bumper, perform the blind spot monitor beam axis confirmation. If any abnormalities are found, perform the blind spot monitor sensor installation condition inspection.

NEXT

3.

INSPECT BATTERY VOLTAGE

(a) Measure the battery voltage.

Standard Voltage:

11 to 14 V

If the voltage is below 11 V, replace or recharge the battery before proceeding to the next step.

NEXT

4.

CHECK CAN COMMUNICATION SYSTEM*

(a) Use the Techstream to check if the CAN communication system is functioning normally.

Click here

Result

Proceed to

CAN communication system DTCs are not output.

A

CAN communication system DTCs are output.

B

B

GO TO CAN COMMUNICATION SYSTEM

A

5.

CHECK FOR DTC AND FREEZE FRAME DATA*

(a) Refer to DTC Check / Clear for the blind spot monitor system.

Body Electrical > Blind Spot Monitor Master > Trouble Codes Body Electrical > Blind Spot Monitor Slave > Trouble Codes

(b) Record or print DTCs and freeze frame data, if necessary.

Click here

Result

Proceed to

DTCs are not output.

A

DTCs are output.

B

B

GO TO DIAGNOSTIC TROUBLE CODE CHART

A

6.

PROBLEM SYMPTOMS TABLE

(a) Refer to Problem Symptoms Table.

Click here

Result

Proceed to

Fault is not listed in Problem Symptoms Table.

A

Fault is listed in Problem Symptoms Table.

B

HINT:

If the symptom does not recur and no DTCs are output, attempt to reproduce the symptoms.

Click here

B

GO TO PROBLEM SYMPTOMS TABLE

A

7.

PERFORM TROUBLESHOOTING BASED ON MALFUNCTION SYMPTOM*

(a) Refer to Terminals of ECU.

Click here

(b) Refer to Diagnosis System.

Click here

(c) Refer to Data List / Active Test.

Click here

NEXT

8.

ADJUST, REPAIR OR REPLACE

Result

Proceed to

When adjusting or repairing

A

When replacing

B

B

GO TO STEP 10

A

9.

CLEAR DTC*

(a) Clear the DTCs.

Click here

Body Electrical > Blind Spot Monitor Master > Clear DTCs Body Electrical > Blind Spot Monitor Slave > Clear DTCs
NEXT

GO TO STEP 10

10.

PERFORM BEAM AXIS INSPECTION

(a) Enter Test Mode (refer to Blind Spot Monitor Beam Axis Inspection).

Click here

(b) Confirm the blind spot monitor beam axis display and perform the blind spot monitor beam axis adjustment.

NEXT

11.

PERFORM CONFIRMATION TEST*

NEXT

END

    READ NEXT:

     Operation Check

    OPERATION CHECK PERFORM BLIND SPOT MONITOR BEAM AXIS CONFIRMATION HINT: The blind spot monitor beam axis confirmation is performed to confirm whether the sensor beam axis is correct, and to adjust t

     Customize Parameters

    CUSTOMIZE PARAMETERS CUSTOMIZE BLIND SPOT MONITOR SYSTEM (a) Customizing with the Techstream NOTICE: When the customer requests a change in a function, first make sure that the function can be

     Problem Symptoms Table

    PROBLEM SYMPTOMS TABLE HINT: Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order

    SEE MORE:

     USB Device Malfunction (B1585)

    DESCRIPTION This DTC is stored when a malfunction occurs in a connected device. DTC No. Detection Item DTC Detection Condition Trouble Area B1585 USB Device Malfunction When any of the following conditions is met: A non mass-storage class or incompatible proto

     Disassembly

    DISASSEMBLY PROCEDURE 1. REMOVE CLUTCH DRUM OIL SEAL RING (a) Remove the 4 clutch drum oil seal rings from the stator shaft assembly. 2. REMOVE OIL STRAINER ASSEMBLY (a) Using a T30 "TORX" socket wrench, remove the 2 bolts and oil strainer assembly from the front oil

    © 2023-2024 Copyright www.tocamry.com