Toyota Camry (XV70): Problem Symptoms Table
PROBLEM SYMPTOMS TABLE
HINT:
- Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.
- Inspect the fuses and relays related to this system before inspecting the suspected areas below.
|
Symptom | Suspected Area |
Link |
|---|---|---|
|
System does not operate at all |
Proceed to "Power Source Circuit" |
|
|
CAN communication system |
| |
|
Blind spot monitor sensor RH |
| |
|
System cannot be turned off |
CAN communication system |
|
|
Blind spot monitor sensor RH |
| |
|
"Blind Spot Monitor Unavailable" or "Blind Spot Monitor System Malfunction Visit Your Dealer" is displayed on the multi-information display |
Check abnormality history |
|
|
Blind spot monitor sensor RH |
| |
|
Blind spot monitor sensor LH |
| |
|
Combination meter assembly |
| |
|
"Rear Cross Traffic Alert Unavailable" or "Rear Cross Traffic Alert Malfunction Visit Your Dealer" is displayed on the multi-information display |
Check abnormality history |
|
|
Blind spot monitor sensor RH |
| |
|
Blind spot monitor sensor LH |
| |
|
Combination meter assembly |
|
.gif)
|
Symptom | Suspected Area |
Link |
|---|---|---|
|
Outer rear view mirror indicator RH does not illuminate |
Proceed to "Blind Spot Monitor Beam Axis Confirmation" |
|
|
Outer mirror RH |
| |
|
Outer rear view mirror assembly with cover RH |
| |
|
Blind spot monitor sensor RH |
| |
|
Outer rear view mirror indicator LH does not illuminate |
Proceed to "Blind Spot Monitor Beam Axis Confirmation" |
|
|
Outer mirror LH |
| |
|
Outer rear view mirror assembly with cover LH |
| |
|
Blind spot monitor sensor LH |
| |
|
Outer rear view mirror indicator RH remains illuminated |
Proceed to "Blind Spot Monitor Beam Axis Confirmation" |
|
|
Blind spot monitor sensor RH |
| |
|
Outer rear view mirror indicator LH remains illuminated |
Proceed to "Blind Spot Monitor Beam Axis Confirmation" |
|
|
Blind spot monitor sensor LH |
| |
|
Outer rear view mirror indicator RH does not flash |
Proceed to "Turn Signal Light" in Problem Symptoms Table for the Lighting (EXT) section |
|
|
Blind spot monitor sensor RH |
| |
|
Outer rear view mirror indicator LH does not flash |
Proceed to "Turn Signal Light" in Problem Symptoms Table for the Lighting (EXT) section |
|
|
Blind spot monitor sensor LH |
| |
|
Outer rear view mirror indicator RH continues to flash |
Blind spot monitor sensor RH |
|
|
Outer rear view mirror indicator LH continues to flash |
Blind spot monitor sensor LH |
|
|
Symptom | Suspected Area |
Link |
|---|---|---|
|
Function does not operate at all (Blind spot monitor function operates normally) |
Data list / active test (Reverse) |
|
|
Automatic transmission system (UA80E) |
| |
|
Automatic transmission system (UB80E) |
| |
|
Blind spot monitor sensor LH |
| |
|
While RCTA function is active, outer rear view mirror indicator flashes but RCTA buzzer does not sound. |
Proceed to "Buzzer does not Sound" |
|
|
When shift lever is in R, detection operation is normal but RCTA indicator does not appear on multi-display |
CAN communication system |
|
|
Blind spot monitor sensor RH |
| |
|
Blind spot monitor sensor LH |
| |
|
Radio and display receiver assembly |
| |
|
Rear television camera assembly*1 |
| |
|
Television Camera Controller*2 |
|
- *1: w/ Parking Assist Monitor System
- *2: w/ Panoramic View Monitor System
READ NEXT:
Terminals Of Ecu
TERMINALS OF ECU BLIND SPOT MONITOR SENSOR RH (MASTER)
Terminal No. (Symbol)
Wiring Color Terminal Description
Condition Specified Condition
W5-4 (OMIR) - W5-10 (BRGD)
Diagnosis System
DIAGNOSIS SYSTEM DESCRIPTION (a) Blind spot monitor data and Diagnostic Trouble Codes (DTCs) can be read from the Data Link Connector 3 (DLC3) of the vehicle. When the system seems to be malfunctionin
Dtc Check / Clear
DTC CHECK / CLEAR CHECK DTC (a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG). (c) Turn the blind spot monitor system on.
(d) Turn the Techstream on. (e) Enter the followi
SEE MORE:
Removal
REMOVAL CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced generator assembly removal/installation are shown below. Necessary Procedures After Parts Removed/Installed/R
Inspection
INSPECTION PROCEDURE 1. INSPECT FUEL PUMP ASSEMBLY
(a) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection Condition
Specified Condition
1 - 2 20°C (68°F)
0.45 to 0.55 Ω If the result is not
