Toyota Camry (XV70): How To Proceed With Troubleshooting
CAUTION / NOTICE / HINT
HINT:
- Use the following procedure to troubleshoot the wiper and washer system.
- *: Use the Techstream.
PROCEDURE
|
1. | VEHICLE BROUGHT TO WORKSHOP |
|
.gif)
|
2. | CUSTOMER PROBLEM ANALYSIS |
HINT:
- In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.
- Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.
- The following 5 items are important points for problem analysis:
What
Vehicle model, system name
When
Date, time, occurrence frequency
Where
Road conditions
Under what conditions?
Driving conditions, weather conditions
How did it happen?
Problem symptoms
|
|
3. | READ OUT AND SAVE OPERATION HISTORY |
NOTICE:
- If the vehicle or vehicle controls are operated (for example, during initial inspection when the vehicle is brought in for repair) before operation history has been read out and saved, the operation history information could be lost.
- The function "Read operation history" uses the current system time setting inside the Techstream and the time counter inside the controlling ECU to calculate the timings shown in the operation history. For this reason, before reading out the operation history, first make sure that the Techstream system clock is accurately set to the current time.
(a) Read out and save operation history using the Techstream.
Click here .gif)
|
Tester Display |
|---|
|
Operation History |
|
|
4. | PRE-CHECK |
(a) Measure the battery voltage.
Standard Voltage:
11 to 14 V
If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.
(b) Check the fuses and relays.
(c) Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.
|
|
5. | CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM* |
(a) Using the Techstream, check for CAN communication system DTCs.
Click here
|
Result | Proceed to |
|---|---|
|
CAN DTCs are not output |
A |
| CAN DTCs are output |
B |
| B | .gif) |
GO TO CAN COMMUNICATION SYSTEM |
|
|
6. | CHECK FOR DTC* |
(a) Check for DTCs.
Body Electrical > Wiper > Trouble Codes Body Electrical > Main Body > Trouble Codes|
Result | Proceed to |
|---|---|
|
DTCs are not output |
A |
| DTCs are output |
B |
| B | |
GO TO DIAGNOSTIC TROUBLE CODE CHART
|
|
|
7. | PROBLEM SYMPTOMS TABLE |
(a) Refer to Problem Symptoms Table.
Click here
|
Result | Proceed to |
|---|---|
|
Fault is not listed in Problem Symptoms Table |
A |
| Fault is listed in Problem Symptoms Table |
B |
| B | |
GO TO PROBLEM SYMPTOMS TABLE |
|
|
8. | OVERALL ANALYSIS AND TROUBLESHOOTING* |
(a) Operation Check.
Click here
(b) Data List / Active Test
Click here
(c) Terminals of ECU
Click here
(d) Fail-safe Chart
Click here
(e) Inspection
(f) On-vehicle inspection
|
|
9. | ADJUST, REPAIR OR REPLACE |
|
|
10. | CONFIRMATION TEST |
| NEXT | |
END |
READ NEXT:
Check For Intermittent Problems
CHECK FOR INTERMITTENT PROBLEMS
NOTICE:
If the vehicle or vehicle controls are operated (for example, during initial inspection when the vehicle is brought in for repair) before operation his
Operation Check
OPERATION CHECK CHECK SERVICE POSITION CONTROL
(a) Turn the ignition switch off. (b) Within approximately 45 seconds of turning the ignition switch off, hold the windshield wiper switch assembly in
Utility
UTILITY OPERATION HISTORY HINT: History of Reason for Operation: The windshield wiper motor assembly stores Operation History which can be read using the Techstream, when a malfunction of the wiper an
SEE MORE:
Fail-safe Chart
FAIL-SAFE CHART If any of the following DTCs are stored, the ECM enters fail-safe mode to allow the vehicle to be driven temporarily or stops fuel injection.
DTC Code Component
Fail-Safe Operation Fail-Safe Deactivation Condition
P001100 P001107 P001500 P002100 P002107
P00
Noise Occurs from V-ribbed Belt or Generator Assembly
PROCEDURE
1. CONFIRM PROBLEM SYMPTOM
(a) Confirm the problem symptom.
Symptom Proceed to
Noise occurs from V-ribbed belt.
A Noise occurs from generator assembly.
B
B
GO TO STEP 6
A
2.
CHECK V-RI
