Toyota Camry (XV70): Parts Location
PARTS LOCATION
ILLUSTRATION
|
*A | w/ Side Turn Signal Light |
*B | for A25A-FKS |
|
*C | for 2GR-FKS |
- | - |
|
*1 | HEADLIGHT ASSEMBLY LH |
*2 | HEADLIGHT ASSEMBLY RH |
|
*3 | SIDE TURN SIGNAL LIGHT ASSEMBLY LH |
*4 | SIDE TURN SIGNAL LIGHT ASSEMBLY RH |
|
*5 | FORWARD RECOGNITION CAMERA |
*6 | ECM |
|
*7 | SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) |
*8 | PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
|
*9 | ENGINE ROOM RELAY BLOCK AND JUNCTION BLOCK ASSEMBLY - H-LP LH RELAY - H-LP RH RELAY - DIM RELAY - DRL RELAY (for LED Type Turn Signal Light) - H-LP LH FUSE - H-LP RH FUSE - H-LP HI FUSE - ALT FUSE - DRL FUSE (for LED Type Turn Signal Light) |
*10 | MILLIMETER WAVE RADAR SENSOR ASSEMBLY |
ILLUSTRATION
|
*1 | CENTER STOP LIGHT SET |
*2 | LICENSE PLATE LIGHT ASSEMBLY RH |
|
*3 | LICENSE PLATE LIGHT ASSEMBLY LH |
*4 | REAR LIGHT ASSEMBLY RH - REAR LIGHT LENS AND BODY RH (for LED Type Back-up Light) - REAR LIGHT CORD RH (for LED Type Back-up Light) |
|
*5 | REAR LIGHT ASSEMBLY LH - REAR LIGHT LENS AND BODY LH (for LED Type Back-up Light) - REAR LIGHT CORD LH (for LED Type Back-up Light) |
*6 | REAR COMBINATION LIGHT ASSEMBLY RH - REAR COMBINATION LIGHT LED (for Bulb Type Back-up Light) - REAR COMBINATION LIGHT SOCKET AND WIRE RH (for Bulb Type Back-up Light) - REAR COMBINATION LIGHT CORD RH (for LED Type Back-up Light) |
|
*7 | REAR COMBINATION LIGHT ASSEMBLY LH - REAR COMBINATION LIGHT LED (for Bulb Type Back-up Light) - REAR COMBINATION LIGHT SOCKET AND WIRE LH (for Bulb Type Back-up Light) - REAR COMBINATION LIGHT CORD LH (for LED Type Back-up Light) |
- | - |
ILLUSTRATION
|
*A | w/o Electric Parking Brake |
- | - |
|
*1 | AUTO HIGH BEAM SWITCH |
*2 | AUTOMATIC LIGHT CONTROL SENSOR |
|
*3 | HAZARD WARNING SIGNAL SWITCH ASSEMBLY |
*4 | TURN SIGNAL SWITCH |
|
*5 | STOP LIGHT SWITCH ASSEMBLY |
*6 | STEERING WHEEL SWITCH HOUSING |
|
*7 | PARKING BRAKE SWITCH ASSEMBLY |
*8 | STEERING SENSOR |
|
*9 | AIRBAG SENSOR ASSEMBLY |
*10 | MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
|
*11 | DLC3 |
*12 | COMBINATION METER ASSEMBLY |
|
*13 | INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - TAIL RELAY - BKUP LP RELAY - TAIL FUSE - BKUP LP FUSE - ECU-B NO. 2 FUSE - ECU-DCC NO. 2 FUSE - HAZ FUSE - METER-IG2 FUSE - STOP FUSE - ECU-ACC FUSE |
- | - |
READ NEXT:
System Diagram
SYSTEM DIAGRAM
HEADLIGHT ASSEMBLY CIRCUIT (for Bulb Type Turn Signal Light)
HEADLIGHT ASSEMBLY CIRCUIT (for LED Type Turn Signal Light)
How To Proceed With Troubleshooting
CAUTION / NOTICE / HINT
HINT:
Use the following procedure to troubleshoot the lighting system.
*: Use the Techstream.
PROCEDURE
1. VEHICLE BROUGHT TO WORKSHOP
Operation Check
OPERATION CHECK AUTOMATIC LIGHT CONTROL SYSTEM OPERATION CHECK
NOTICE: Make sure that the customize settings are set to default when performing the automatic light control system operation check.
SEE MORE:
Removal
REMOVAL CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear No. 1 differential mount cushion removal/installation are shown below. Necessary Procedures Afte
Calibration
CALIBRATION
NOTICE:
Initial AWD functions such as acceleration are sometimes affected unless backup memory is cleared.
When the yaw rate and acceleration sensor (airbag sensor assembly) is replaced, Reset Memory must be performed.
RESET MEMORY (a) Turn the ignition switch off. (b) Co
