Toyota Camry (XV70): Cruise Main Indicator Light Circuit
DESCRIPTION
When the dynamic radar cruise control system is turned on using the cruise control main switch, the cruise control indicator (vehicle-to-vehicle distance control mode) illuminates. The ECM uses this and other indicators to indicate the status (presence or absence of a preceding vehicle, vehicle-to-vehicle distance, malfunction of system or related systems) of the dynamic radar cruise control system.
CAUTION / NOTICE / HINT
NOTICE:
- Before replacing the ECM, refer to Registration.
w/ Smart Key System: Click here
.gif)
w/o Smart Key System: Click here
- When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
PROCEDURE
|
1. | PERFORM ACTIVE TEST USING TECHSTREAM (Combination Meter) |
(a) Perform the Active Test according to the display on the Techstream.
Body Electrical > Combination Meter > Active Test|
Tester Display | Measurement Item |
Control Range | Diagnostic Note |
|---|---|---|---|
|
Multi Display All (White) |
Multi-information display (White display) |
ON | Confirm that the vehicle is stopped with the ignition switch ON. |
|
Tester Display |
|---|
| Multi Display All (White) |
|
Result | Proceed to |
|---|---|
|
The multi-information display in the combination meter assembly turns on according to the operation of the Active Test |
A |
| The multi-information display in the combination meter assembly does not turn on according to the operation of the Active Test |
B |
| B |
.gif) | GO TO METER / GAUGE SYSTEM |
|
.gif)
| 2. |
READ VALUE USING TECHSTREAM (Radar Cruise1) |
(a) Read the Data List according to the display on the Techstream.
Powertrain > Cruise Control > Data List|
Tester Display | Measurement Item |
Range | Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
Cruise Indicator | Cruise control indicator status |
ON or OFF | ON: Cruise control indicator illuminates OFF: Cruise control indicator turns off |
- |
|
Tester Display |
|---|
| Cruise Indicator |
|
Result | Proceed to |
|---|---|
|
The cruise control indicator illuminates and turns off according to the operation of the cruise control main switch |
A |
| The cruise control indicator does not illuminate but the Data List items change according to the operation of the cruise control main switch |
B |
| The cruise control indicator does not illuminate and the Data List items do not change according to the operation of the cruise control main switch |
C |
| A |
| PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
| B |
| REPLACE COMBINATION METER ASSEMBLY |
| C |
| REPLACE ECM for A25A-FKS: Click here for 2GR-FKS: Click here
|
READ NEXT:
Cruise SET Indicator Light Circuit
DESCRIPTION The ECM illuminates the cruise SET indicator by sending request signals to the combination meter assembly via CAN communication. The cruise SET indicator illuminates when the dynamic radar
Components
COMPONENTS ILLUSTRATION
*1 FORWARD RECOGNITION CAMERA
*2 FORWARD RECOGNITION LATCH
*3 NO. 1 FORWARD RECOGNITION COVER
*4 NO. 2 FORWARD RECOGNITION COVER
SEE MORE:
Installation
INSTALLATION PROCEDURE 1. INSTALL CAMSHAFT TIMING GEAR BOLT
(a) Make sure that the No. 1 cylinder is at TDC/compression. HINT:
Check that the cutout of the camshaft timing gear assembly is at the top and align the timing mark (cutout) of the crankshaft pulley with the timing mark on the timing c
Transmission Range Sensor "A" Circuit Open (P070513,P070562)
DESCRIPTION The park/neutral position switch assembly detects the shift lever position and sends signals to the ECM.
DTC No. Detection Item
DTC Detection Condition Trouble Area
MIL Memory
Note P070513
Transmission Range Sensor "A" Circuit Open
When the engi
